Berenson Overture Series 3-3/4" (95 mm) Center to Center Rustic Copper Pull, - 7112-1RC-C

Berenson Rustic Copper Pull For Cabinet Jobs

Berenson Overture Series rustic copper pull gives cabinets a defined 3-3/4 inch center to center mounting layout, which sets consistent handle spacing across doors and drawers for a uniform, planned look on finished projects. The zinc die cast material forms a solid, single-piece pull body, so the handle feels stable in use and holds alignment once fastened to the cabinet front. Its rustic copper finish presents a warm, aged tone, which helps this pull coordinate with traditional wood cabinetry and similar warm metal finishes on adjacent hardware. Overall length of 5-3/8 inch stretches slightly beyond the drilling pattern, providing grip area at each end without crowding typical cabinet face sizes. A projection of 1-1/16 inch brings the pull out from the face just enough for fingers to wrap behind it, supporting comfortable opening of doors and drawers.

Key Overture Pull Details For Practical Use

• The 3-3/4 inch center to center drilling dimension defines hole placement, which simplifies layout and repeat drilling when installing multiple pulls on a run of cabinets.
• The 5-3/8 inch overall length covers the drilling span with some extension, which helps the pull visually anchor the door or drawer front while leaving margin near edges.
• The 1 inch base diameter at each contact point sets a clear bearing surface on the cabinet face, which helps distribute clamping force of the fasteners over a defined area.
• The 3/4 inch width across the grip creates a defined handling surface, which supports a comfortable grasp for routine cabinet opening and closing.
• The rustic copper finish on the zinc die cast pull establishes a consistent color tone, which helps tie together hardware details across a kitchen or bath layout.

Mounting Dimensions And Screw Details For Pulls

The OVERTURE PULL 96MM CC RUSTIC COPPER provides a 96 mm, or 3-3/4 inch, center to center mounting specification, giving a clear metric and imperial reference for drilling cabinet fronts. M4 x 45mm screws are specified for fastening, so the pull is set up around a known machine screw diameter and length suitable for typical cabinet door and drawer thicknesses. A base diameter of 1 inch defines how much of the pull contacts the surface, giving a predictable footprint around each screw location. With a projection of 1-1/16 inch from the mounting surface, the handle stands off the face enough to clear fingers between the grip and the cabinet front. The 3/4 inch width and 5-3/8 inch overall length work together to create a balanced handle profile that spans the mounting points cleanly.

Using This Berenson Pull In Cabinet Projects

Where The Berenson 7112-1RC-C Pull Fits Best

This Berenson 7112-1RC-C pull from the Overture Series is set up for cabinet applications that match its 3-3/4 inch center to center requirement, so it suits doors and drawers already drilled or planned for that spacing. The zinc die cast construction fits well in decorative hardware roles on kitchen, bath, or built-in cabinetry where a metal pull is preferred. Its rustic copper finish gives it visual alignment with cabinetry that uses warm stains, glazes, or coordinating copper-toned hinges and related decorative hardware. With a 5-3/8 inch overall length and 3/4 inch width, the pull fits comfortably on standard cabinet rails and drawer fronts without overwhelming narrow faces, so it adapts to a range of cabinet sizes using the same mounting pattern. The 1-1/16 inch projection also positions the grip away from the surface, fitting spaces where finger clearance in front of the cabinet is needed.

Details That Support Consistent Cabinet Results

The defined 96 mm center to center dimension on this zinc die cast rustic copper cabinet pull supports repeatable layout across multiple cabinets, because installers can rely on a single drilling pattern for each handle location. M4 x 45mm screws as the fastening specification give a consistent fastener interface through the door or drawer front, which helps the pull clamp evenly to the 1 inch diameter base contact areas on both ends. The 3/4 inch width paired with 1-1/16 inch projection provides a grip profile that remains the same from cabinet to cabinet, reducing variation in hand clearance or feel between doors and drawers. Because the pull length is fixed at 5-3/8 inch, each installation presents the same visual span across the front, supporting alignment with adjacent pulls in rows or banks of cabinetry. The rustic copper finish across the Overture Series pull body keeps color and sheen uniform, which helps create a consistent decorative hardware line throughout a project.

Common Questions About This Rustic Copper Pull

Selecting This Pull For Cabinet Hardware Runs

The Berenson Overture Series rustic copper pull combines a 3-3/4 inch center to center layout, zinc die cast construction, and a rustic copper finish, giving cabinet projects a defined drilling pattern and coordinated appearance. With its 5-3/8 inch length, 1 inch base diameter, 3/4 inch width, and 1-1/16 inch projection, the pull offers consistent proportions and clearance from door to door. For cabinet work built around 96 mm or 3-3/4 inch handle spacing, this OVERTURE PULL 96MM CC RUSTIC COPPER provides a straightforward way to align decorative hardware across kitchens, baths, and built-ins.