
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
HALF MOON WIRE PULL SATIN NICKEL describes a compact cabinet and drawer pull that uses a half-moon wire profile to give a slim gripping surface, which helps on tight face frames and narrow drawer fronts where bulky pulls can interfere with adjacent fronts. The Metropolis Series designation ties this pull to a coordinated decorative hardware family, so matching additional handles on the same job stays straightforward across a kitchen, bath, or office run. The 2-1/2 inch (64 mm) center to center drilling sets the hole spacing, which matters when laying out new fronts or lining up with existing bores during replacement work. The manufacturer-specified 3-7/8 inch overall length gives enough bar to grab while still fitting smaller doors, so installers can keep consistent style on both small and medium-width fronts. The satin nickel finish keeps the appearance subdued, which helps it work across a range of door finishes without visual noise on finished cabinetry.
The 2-1/2 inch (64 mm) center to center spec sets the exact distance between mounting points, so installers can position drilling templates and boring equipment confidently across multiple doors. The 3-7/8 inch overall length then indicates how far the pull runs past the holes, which helps with aligning the handle relative to rail edges and neighboring fronts. The 7/8 inch projection determines how far the pull stands off the surface, which matters when cabinets are near walls or appliances where extra depth could interfere with operation. The 3/8 inch width keeps the pull narrow on the face, supporting clean alignment on slim drawer fronts that do not leave much flat area. The satin nickel finish pairs with the Metropolis Series styling to give a modern but not aggressive look, so hardware layout stays consistent with contemporary casework.
The 2-1/2 inch (64 mm) center to center measurement fits layouts designed around shorter drilling patterns, which is useful on compact kitchen cabinets, vanity drawers, and small utility doors that cannot accept longer handles. The specified 3-7/8 inch length keeps the pull proportionate on these smaller fronts, so the hardware does not dominate narrow rails. The 7/8 inch projection still offers clearance for fingers even when the pull is centered on thin drawer faces, helping daily operation feel natural. The 3/8 inch width keeps visual weight low, which can be valuable on dense cabinet runs where many pulls sit close together. The satin nickel finish from the Metropolis Series maintains a consistent tone across different cabinet banks, supporting unified hardware appearance in open-plan spaces. The zinc die cast construction suits typical interior cabinet and drawer use, so this pull can be applied across residential and light commercial millwork runs built around decorative hardware and moldings.
The defined 2-1/2 inch center to center dimension allows jigs and drilling patterns to be reused from job to job whenever this pull is specified, which can speed layout on repeat Metropolis Series installations. Knowing the 3-7/8 inch overall length when planning hardware positions lets installers keep a consistent offset from stile and rail edges, improving visual alignment over long cabinet runs. The 7/8 inch projection figure helps when checking clearances on doors near corners or tall panels, reducing the chance that hardware interferes with adjacent surfaces when doors swing. The 3/8 inch width allows a consistent reveal around the pull on narrow faces, supporting clean sight lines on banks of drawers. The satin nickel finish is part of the defined product description, so finish selection across a project can be specified by that term. The Belwith Keeler branding and P2921-SN part number give a clear reference for drawings, order lists, and future refits when matching the same pull later.
The P2921-SN uses a 2-1/2 inch (64 mm) center to center spacing, which defines the hole distance for drilling and makes it suitable for shorter mounting layouts on doors and drawers.
The Metropolis Series satin nickel pull has a stated 3-7/8 inch length, giving enough bar to grip while staying in proportion on smaller cabinet and drawer fronts.
The cabinet pull has a 7/8 inch projection, so it stands off the surface enough for a comfortable handhold without extending excessively into walkways.
The half moon wire pull has a 3/8 inch width, creating a slim profile that suits narrow stiles and drawer fronts where space for hardware is limited.
The P2921-SN cabinet pull is made from zinc die cast material, giving a solid metal body suitable for repeated opening and closing on interior cabinetry.
The Metropolis P2921-SN pull has a satin nickel finish, providing a soft metallic look that coordinates with many cabinet colors and modern interior styles.
The defined 2-1/2 inch (64 mm) center to center spacing, 3-7/8 inch overall length, and 7/8 inch projection give clear sizing for planning your cabinet hardware layout. The satin nickel finish, zinc die cast construction, and Metropolis Series identity supply a consistent style choice for matching pulls across doors and drawers. With the Belwith Keeler brand and P2921-SN part number, this half moon wire pull offers a clearly specified option when standardizing hardware on new builds or refacing work at Wurth Baer Supply.
Sold In: 1 Each