Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
ProCarpenter 16' Standard/Reverse Tape Measure provides a 16ft measuring length that handles typical cabinet, trim, and general woodworking layouts in one pull, which keeps layout work moving without constant repositioning. The Fastcap ProCarpenter identity and PSSR-16 part number clearly tie this tool to the Pro Carpenter tape line, which helps installers match it with other shop standards when restocking or outfitting crews. A 1 inch thick tape supports an 8ft standoff, so the blade extends rigidly for long horizontal or overhead measurements, which cuts down on sagging and re-measuring on wider panels or longer runs. Standard and reverse readings on the blade let you read measurements from either working side, which helps when switching hands around cabinets, cases, or benchtop jigs. Right and left reading markings further support this from-both-sides use, which matters when working in tight spaces.
The 1 inch thick tape on this Fastcap ProCarpenter tape measure gives a wider reading surface, which stabilizes the blade against edges and helps hold straight reference lines along case sides or face frames. Standard and reverse tape readings on the same 16ft blade allow measurements to be read from either orientation, which helps when the printed face needs to be flipped toward or away from the user during awkward cabinet or shop setups. Right and left reading markings mean graduations make sense when used in either hand, which is helpful on repetitive layout where the user shifts positions around a workpiece. Dual thumb and finger locks give control over blade hold, so the user can set the tape with whichever hand is in the better position, maintaining tension on the hook point without blade creep while marking.
The TAPE MSR, STD REVERSE, 16FT description identifies this tool as a 16ft standard and reverse reading tape measure, which aligns it well with common cabinet runs, closet sections, and benchtop jigs that seldom exceed that range. All Pro Carpenter tapes carrying the PSSR-16 designation share the erasable note pad, so repeated layout dimensions for a job can be parked on the casing and referenced at the saw, router table, or assembly bench. The built-in pencil sharpener integrated into the tape casing pairs directly with those written notes, keeping a single layout pencil performing consistently from rough framing measurements through final trim layout. Easy to read fraction call outs to 1/16 inch on the blade support detail work in fine woodworking, where fitting doors, drawers, or trim often depends on reading small fractional differences quickly under normal shop lighting.
The erasable note pad on the tape casing side directly links measurements to written dimensions, which helps keep repeated cut lists and on-the-fly adjustments attached to the same ProCarpenter 16' Standard/Reverse Tape Measure used to capture them. An ergonomic belt clip keeps that tape at a consistent position on the user, which supports a repeatable reach pattern from workpiece to tape and then back, speeding up cycles during production-style cabinet or fixture work. Dual thumb and finger locks allow the blade to be held with either hand, so measurements can be frozen at length without twisting the user's wrist, which makes it easier to reproduce markings from the same reference edge throughout a job. The 8ft standoff rating of the 1 inch thick tape keeps the blade straight across longer spans, which improves consistency from one measurement to the next when working across full sheet goods or long cabinet assemblies.
The ProCarpenter PSSR-16 tape measure provides a 16ft blade length, which covers most cabinet, trim, and woodworking layout tasks without needing an additional longer tape for typical shop work.
The standard and reverse readings on the blade allow the tape to be read from either side, which helps when measuring from opposite directions or switching hands around cabinets, panels, or jigs.
The 8ft standoff rating means the 1 inch thick tape blade can extend about 8 feet before bending, which supports longer unsupported measurements across wider workpieces or spans.
The erasable note pad on the tape casing side lets you record dimensions directly on the tool, which keeps important measurements visible at the cut or assembly area.
The built-in pencil sharpener on the casing keeps a layout pencil ready at the measuring point, which helps maintain crisp lines and reduces time spent away from the workpiece.
The dual thumb and finger locks let the blade be held with either hand, which provides flexible control over blade position and helps prevent slipping during marking.
The Fastcap ProCarpenter 16' Standard/Reverse Tape Measure combines a 16ft blade, 1 inch thick tape, and 8ft standoff with right and left reading markings, which supports common woodworking dimensions from multiple positions. The erasable note pad, built-in pencil sharpener, and ergonomic belt clip keep measuring, marking, and quick notes centered on a single tool, which helps streamline layout work around saws, benches, and installed cabinetry. For shops and installers needing a tape that ties measuring, notation, and marking into one workflow, this PSSR-16 Pro Carpenter tape measure fits directly into everyday cabinet and woodworking tasks.
Sold In: 1 Each
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 1 Each |  FAPSS-R-25 Mfr# PSSR-25 | ProCarpenter™ 25' Standard/Reverse Tape Measure |