Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Berenson Zurich recessed pull is a zinc die cast handle from the Zurich Series that provides a recessed grip for cabinet and furniture fronts, so doors and drawers operate using a low-profile pull point built into the face.
The polished chrome finish reflects the surrounding surfaces, which gives cabinet runs a bright, contemporary look while keeping the pull visually consistent across multiple fronts in the same project.
The pull has a center to center length of 8-13/16 inches, or 224 mm, which sets the hole spacing between mounting points and controls how it aligns across wider drawers or doors in a layout.
The total length of 4-1/2 inches defines the visible span of the recess pull on the surface, so it establishes how much linear grip area is present on each cabinet front.
The projection of this Zurich recessed pull is 1/8 inch, which keeps the hardware very close to the cabinet face so fronts maintain a streamlined profile while still providing enough offset for a hand to catch the recessed grip.
The width of 1-11/16 inches determines how far the pull spans across the face vertically or horizontally, which influences how much surface area is devoted to the recess and how it visually balances on different door or drawer sizes.
Base dimensions of 3-21/32 inches define the footprint where the pull meets the cabinet surface, which affects the contact area on the substrate and the visual block of metal against the panel material.
The Zurich Series name identifies this pull within Berenson Corporation decorative hardware, which helps align it with other handles and pulls in the same family when planning a coordinated cabinet hardware layout.
This Zurich Series recessed pull from Berenson Corporation sits in the Decorative Hardware & Moldings category under Handles and Pulls, so it functions as a primary operating grip for cabinet doors or drawers in woodworking projects.
The handle is a recessed pull, which means the grip area is set into the face rather than projecting outward, so cabinets maintain a flatter appearance while still providing a defined handhold for daily opening and closing.
The polished chrome finish places this pull in a finish group commonly used on modern and transitional cabinetry, which allows it to coordinate visually with polished chrome hinges, knobs, and other decorative hardware in the same room.
The 8-13/16 inch, or 224 mm, center to center dimension positions this pull for use on wider fronts where a longer mounting span supports proportionally spaced hardware across the width of drawers or doors.
The width of 1-11/16 inches and base dimensions of 3-21/32 inches define a relatively compact footprint for a pull with this center spacing, which makes it suitable where a recessed pull is preferred but excessive face coverage is not desired.
Being part of the Berenson product class for Handles and Pulls, this Zurich recessed pull slots into standard decorative hardware planning, so it can be specified alongside other Berenson pieces while keeping measurements consistent with cataloged dimensions.
The clearly stated 224 mm center to center measurement lets installers repeat hole spacing accurately across multiple cabinet fronts, which helps rows of Zurich recessed pulls align from door to door without visual step-offs.
The 4-1/2 inch length value gives a fixed reference when aligning the pull relative to edge reveals, which can simplify layout lines and reduce variation across tall doors and varying drawer heights.
A projection of 1/8 inch provides a known offset from the face, which aids in planning clearances near adjacent doors, panels, or appliance fronts where extra stand-off might interfere with neighboring surfaces.
The width of 1-11/16 inches can be used to position the pull so that equal margins are maintained above and below, which supports consistent visual spacing when working across banks of drawers with different front heights.
Base dimensions of 3-21/32 inches act as a precise footprint reference, which can help when routing or planning recess areas so that the metal base aligns with prepared cutouts or flat mounting zones on the cabinet face.
The Berenson Zurich Series identification connects this specific 6692-126-B recessed pull to a named collection, which simplifies documentation on drawings, cut lists, and hardware schedules because each measurement traces back to a defined series and part number.
The Berenson Zurich recessed pull has a center to center dimension of 8-13/16 inches, or 224 mm, which establishes the exact hole spacing used when creating mounting points.
The Zurich recessed pull has a projection of 1/8 inch, so it stays close to the cabinet surface while still defining the geometry of the recessed grip on the face.
The Zurich Series recessed pull is made from zinc die cast material, which provides a metal body suitable for typical cabinet and furniture hardware applications.
The 6692-126-B Berenson Zurich recessed pull has a polished chrome finish, so it visually coordinates with other polished chrome decorative hardware in a project.
This Zurich recessed pull lists a length of 4-1/2 inches, a width of 1-11/16 inches, and base dimensions of 3-21/32 inches, giving clear references for planning its footprint.
This polished chrome recessed pull belongs to the Zurich Series by Berenson Corporation, linking it to a defined decorative hardware collection and style group.
The Berenson Zurich recessed pull in polished chrome combines zinc die cast construction, a 224 mm center to center dimension, and clearly stated length, width, projection, and base measurements, so it suits cabinet projects that rely on precise, repeatable hardware layout.
