Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Berenson stainless steel pull 128mm is a cabinet handle from the Stainless Steel Series that uses a 5-1/16 inch center to center screw spacing, so it lines up with standard 128 mm boring on many cabinet and drawer fronts. The pull is produced with grade 304 stainless steel, which provides a solid stainless construction that supports use in typical kitchen, bath, or shop environments where metal hardware sees regular handling. The stainless steel finish matches the stainless material, giving a uniform appearance that fits projects calling for a clean, metal look. The pull has a 7 inch overall length, so it covers existing hole locations while giving enough hand clearance for a comfortable grip on doors or drawers. A 1 inch by 1/2 inch base layout, created by the 1/2 inch base diameter and 1/2 inch width, sets a defined footprint on the front, which helps with consistent alignment across multiple fronts.
The 5-1/16 inch center to center measurement on the Berenson 7068-9SS-C pull defines the drilling pattern, so installers can mark two points exactly 128 mm apart for accurate hole placement. The pull fastens using M4 x 45mm screws, so it matches standard metric cabinet screw threads while giving extended length for going through typical cabinet door or drawer front thicknesses. With a 7 inch overall length, the handle extends beyond the mounting holes at both ends, which provides visual balance on wider fronts or when spanning between stiles. The 1-1/4 inch projection sets a fixed standoff from the surface, so all pulls in a run will sit at the same distance from the door or drawer faces, supporting a uniform look along cabinet banks.
This pull is part of the Stainless Steel Series, so it is intended for applications where stainless steel decorative hardware is desired on cabinets or similar casework. The grade 304 stainless steel construction supports use in residential or commercial woodworking projects where metal handles on doors and drawers see regular contact, such as kitchens, bathrooms, and storage areas. With a 7 inch overall length and 5-1/16 inch (128 mm) center to center spacing, the pull suits fronts sized to accept mid-length handles, allowing it to work across both doors and many drawer widths in the same line of cabinetry. The 1/2 inch width and 1/2 inch base diameter keep the visual profile modest, which works well on face frames or frameless cabinet designs where a streamlined stainless pull is part of the layout.
The defined 5-1/16 inch center to center dimension allows installers to repeat the same drilling pattern across multiple cabinet fronts, which helps keep hardware alignment consistent along doors and drawers. The use of M4 x 45mm screws means the pull interfaces with a widely used metric thread size, so installers can run the same driver bits when fastening the pulls during a cabinet installation. The 1-1/4 inch projection maintains consistent clearance behind the pull, which helps users get their fingers behind the handle without contacting the door or drawer face, reducing wear on finished surfaces. The 1/2 inch base diameter sets a known bearing area where the pull meets the wood or panel, which helps distribute contact at each mounting point and assists with straight, repeatable positioning relative to door edges. The stainless steel material and finish combination keeps the appearance uniform across every pull, which supports a cohesive hardware look when many handles are installed on a single project.
The Berenson stainless steel pull uses a 5-1/16 inch (128 mm) center to center size, which sets the hole spacing for mounting on cabinet doors or drawers.
The 7068-9SS-C pull is produced with grade 304 stainless steel, which provides a solid stainless construction for use as decorative cabinet hardware.
This stainless steel pull has a 7 inch overall length, which spans beyond the mounting holes to give a comfortable gripping area on doors and drawers.
The Berenson pull uses M4 x 45mm screws, so it mounts with a standard metric thread size commonly used for cabinet hardware installations.
The pull has a 1-1/4 inch projection, setting how far it stands off the cabinet surface to provide finger clearance behind the handle.
The Berenson Stainless Steel Series pull has a 1/2 inch width, which gives it a slim front profile while still providing a defined gripping surface.
The Berenson Corporation 7068-9SS-C pull combines a 5-1/16 inch (128 mm) center to center drilling pattern with grade 304 stainless steel construction, so it suits cabinet projects built around 128 mm hardware layouts. The 7 inch length, 1-1/4 inch projection, and 1/2 inch width create a balanced handle size that works across many doors and drawers, supporting a consistent look on runs of cabinetry. For woodworking installations that call for Stainless Steel Series decorative hardware from Wurth Baer Supply, this stainless steel finish pull delivers defined dimensions for straightforward layout and repeatable mounting.
Sold In: 1 Each
