Berenson Vibrato Series 3-3/4" (95 mm) Center to Center Verona Bronze Pull, - 7890-1VB-P

Vibrato Pull 96mm CC Verona Bronze For Cabinets

Vibrato pull 96mm CC Verona bronze is a Berenson Vibrato Series cabinet pull designed to give doors and drawers a consistent grip point and visual line across the run. The zinc die cast construction forms a rigid handle that supports repeated everyday use on cabinets in woodworking projects. The Verona Bronze finish provides a warm, darker tone that coordinates with other bronze-colored decorative hardware in the space. The 3-3/4 inch (96 mm) center to center drilling sets a standard mounting spread that works well for many cabinet layouts where handles align across multiple fronts. The overall 4-15/16 inch length extends slightly beyond the drill points, creating a balanced look on both narrow and wider drawer fronts. A projection of 1-1/8 inches gives fingers room behind the pull, which helps when opening heavier doors or deeper drawers in a shop, kitchen, or office install.

Key Berenson Vibrato Pull Details For Projects

• The Vibrato Series designation identifies this pull within Berenson decorative hardware, which helps keep style and finish consistent when planning multiple cabinet runs or coordinating with other Vibrato pieces.
• The zinc die cast material creates a solid, molded handle body that maintains its shape under repeated pulling forces, supporting long-term use on frequently opened cabinet doors and drawers.
• The Verona Bronze finish provides a defined bronze tone that sets the visual character of the hardware, helping designers and installers coordinate with hinges, faucets, and other bronze-finished components.
• The 3-3/4 inch (96 mm) center to center dimension aligns with a common drilling pattern, which is useful when laying out new cabinet fronts or matching existing 96 mm hole spacing during replacement work.
• The 4-15/16 inch overall length gives the pull enough span to look proportional on standard drawer widths, helping maintain visual balance on both small doors and wider banked drawers.
• The 1-1/8 inch projection and 11/16 inch width define the gripping area, giving fingers clearance behind the pull while keeping the handle profile tight to the face for a clean cabinet look.

Mounting And Fit Details For This Verona Bronze Pull

This Berenson Vibrato Series pull uses a 3-3/4 inch (96 mm) center to center mount, so the two mounting points land on that drilling spread for cabinet doors and drawers. The specified screw size of 8-32 x 1 inch sets the thread and length standard for the mounting fasteners, which ties directly to typical cabinet door and drawer front thicknesses in woodworking applications. The base dimensions of 15/16 inch define the footprint where the pull meets the surface, helping installers understand how much space the feet will cover on the door or drawer face. The 11/16 inch width carries through the handle bar, which helps determine how much flat surface is needed so the pull sits fully on the stile or rail without overhanging unwanted edges.

Using The Vibrato Series Pull In Cabinet Work

Where This Verona Bronze Vibrato Pull Performs Best

The Berenson Vibrato Series 3-3/4 inch center to center Verona Bronze pull fits cabinet doors and drawers that are drilled on the 96 mm pattern, so it adapts well to many standard kitchen, bath, or office runs using that spacing. The 4-15/16 inch length allows the pull to sit comfortably on typical cabinet doors and mid-size drawers, so it works across upper wall cabinets, base units, and smaller utility cabinets in woodworking projects. The Verona Bronze finish brings a darker bronze tone that can tie together other bronze-finished hardware, which is useful when a project calls for coordinated handles, knobs, and hinges across a room. The 11/16 inch width keeps the handle visually slender, so it suits face frames, frameless doors, and narrow rails where a bulkier pull could crowd the design. The 1-1/8 inch projection creates an ergonomic clearance behind the handle, which helps hands get a secure grip when opening full drawers or tall pantry doors.

Why These Size And Material Details Support Consistent Results

The zinc die cast material gives this pull a molded, uniform body, which supports consistent sizing from piece to piece when a project uses many handles along large cabinet runs. The 3-3/4 inch (96 mm) center to center dimension sets a repeatable drilling pattern, which helps maintain straight handle lines across multiple doors and drawers in a bank. The 4-15/16 inch overall length leaves some bar beyond the screw holes, which visually centers the grip area on the front and supports better hand placement for users. The 15/16 inch base dimensions define a modest but clear footprint at each end, which helps cover the drill points cleanly while leaving enough surrounding door surface visible for a balanced appearance. The specified 8-32 x 1 inch screw size aligns with a standard cabinet hardware thread, which simplifies planning when matching to typical door and drawer front thicknesses used in woodworking and cabinet shops. Together, these measured details give installers predictable results when aligning handles, matching existing 96 mm layouts, or repeating the same hardware across multiple rooms.

Common Questions About This Vibrato Series Cabinet Pull

Select This Verona Bronze Pull For 96mm Layouts

The Berenson Vibrato Series 3-3/4 inch (96 mm) center to center Verona Bronze pull combines a zinc die cast body, 4-15/16 inch length, and 1-1/8 inch projection to support everyday cabinet use. The defined Verona Bronze finish and 11/16 inch width help this pull integrate into cabinet runs where a coordinated bronze look and standard 96 mm drilling pattern are part of the design and installation plan.