Company Information
Services
Approved US Government VendorCage Code: 1UXJ6
Copyright © 2004-2026, Würth Baer Supply Company. All Rights Reserved.
Copyright © 2004-2026, Würth Baer Supply Company. All Rights Reserved.
Traditional Series solid brass pull gives cabinet doors and drawers a defined 4 inch center to center gripping point, which helps line up drilling and keeps handle spacing consistent across a run of fronts. The pull is made from solid brass, so the core material provides a dense feel and stable base for repeated use in busy areas. A polished chrome finish is applied over the brass, bringing a bright, reflective surface that matches polished chrome hinges and other visible hardware. Schaub and Company identifies this pull as part number 742-26, tying it directly to the Traditional Series line for repeat ordering or coordinated layouts. Overall length is 5-1/8 inches, so the handle overhangs the mounting holes slightly on each side, giving visual balance on standard cabinet face widths.
The 4 inch center to center measurement governs where to drill through cabinet doors and drawer fronts, which lets jigs or templates be set once for repeat work. With a 5-1/8 inch overall length, the pull leaves a short extension beyond each mounting hole, which helps position it symmetrically on medium-width fronts. The 1-1/8 inch projection determines how far the gripping surface stands off the wood, creating space for fingers while limiting how much the handle protrudes into walkways. The 8-32 x 1 inch screw size defines the thread engagement and reach through typical cabinet materials, coordinating the pull with standard cabinet construction thicknesses.
This Schaub and Company Traditional Series solid brass pull works on cabinet doors and drawer fronts that accept a 4 inch center to center drilling pattern, aligning with many common residential and shop-built layouts. The 5-1/8 inch overall length suits medium-width doors and drawers, where a handle slightly longer than the hole spacing gives a balanced look without overwhelming the face. A polished chrome finish across the pull coordinates with polished chrome decorative hardware and fittings in the same room, which helps maintain a consistent appearance across cabinets, fixtures, and visible fasteners. The solid brass construction under the finish supplies a firm, weighty base, supporting regular opening and closing in areas such as kitchens, baths, and storage runs.
The fixed 4 inch center to center measurement lets installers set up drilling patterns or routing jigs once, then repeat the same hole spacing across a job, which saves layout time and keeps pulls aligned. A 1-1/8 inch projection defines the stand-off from the cabinet face, providing predictable finger clearance for users and a known profile for doors that open near walls or adjacent cabinets. Because the pull length is 5-1/8 inches, layout marks can be centered relative to the door or drawer edge while still leaving enough handle on each side of the holes to grip easily. The specified 8-32 x 1 inch screw size ties the pull to a standard cabinet fastener specification, which aids in planning drilling depth and thread engagement in typical door and drawer front thicknesses. The polished chrome finish over solid brass keeps the visible surface bright while the brass core provides a solid base, combining appearance with a substantial feel during daily operation.
The Traditional Series solid brass pull has a 4 inch center to center dimension, so mounting holes are spaced 4 inches apart, which matches many cabinet drilling patterns.
The Schaub and Company 742-26 pull is 5-1/8 inches long overall, giving some handle length beyond the mounting holes for a balanced look on doors and drawers.
The solid brass pull has a 1-1/8 inch projection, setting how far it stands off the cabinet face and defining finger clearance during normal use.
The Traditional Series pull uses a polished chrome finish, giving a bright reflective surface that coordinates with other polished chrome decorative hardware.
The Schaub 742-26 pull is made from solid brass, providing a dense core that supports repeated opening and closing on cabinet doors and drawers.
The cabinet pull uses 8-32 x 1 inch screws, so the threads and length align with common cabinet door and drawer front thicknesses in typical installations.
The Schaub and Company Traditional Series solid brass pull with 4 inch center to center spacing, 5-1/8 inch overall length, and 1-1/8 inch projection gives clear mounting and clearance values for cabinet work. A polished chrome finish over solid brass ties the handle visually to polished chrome decorative hardware while maintaining a substantial feel. When a project calls for a defined 4 inch drilling pattern and a polished chrome appearance, this 742-26 pull provides the documented dimensions needed for planning cabinet door and drawer front layouts.