Hickory Hardware Metropolis pull defines this Belwith Keeler handle as part of the Metropolis collection, so it matches that series when you are coordinating cabinet hardware on a job. The 3-3/4 inch center to center dimension sets a precise hole spacing, which matters when drilling new fronts or reusing existing bores on cabinet doors and drawers. Its overall length of 4-3/4 inches gives comfortable hand clearance across typical residential cabinet widths, making regular opening and closing predictable for clients. The 1 inch projection keeps the pull standing off the face just enough for fingers, which helps reduce knuckle contact with the door surface. A width of 1/2 inch provides a slim profile across the fascia, supporting a cleaner visual line on modern or transitional cabinetry while still giving enough surface for a solid grip.
The 3-3/4 inch center to center dimension on this PA0221-SN satin nickel pull gives a clear drilling target, which is useful when setting up jigs for repetitive cabinet door or drawer installations. Because that measurement is also 96 mm, it aligns with metric layouts where 96 mm spacing is standard, helping on projects that mix imperial and metric planning. The 4-3/4 inch overall length reserves enough space on the rail or stile so the pull sits centered without overhanging narrow frames. With a 1 inch projection, this Metropolis series pull stands off the surface consistently, allowing fingers to wrap behind the bar without rubbing the face of the cabinet during operation. The 1/2 inch width keeps the contact area defined so the installer can visually square the pull to edges while tightening for a straight, repeatable line.
This Belwith Keeler Metropolis series 96mm cabinet pull is suited to cabinet doors and drawers where a 3-3/4 inch center to center layout is desired, because it sets a dependable screw pattern across the run. The zinc die cast construction supports everyday use on kitchen, bath, or built-in cabinetry, since the rigid body holds alignment when the hardware is repeatedly pulled. Its satin nickel finish ties into satin nickel decorative hardware and moldings, helping the installer carry one finish across hinges, knobs, and pulls in the same room. The 4-3/4 inch length fits comfortably on many standard-width drawer fronts, so the pull can be centered without overpowering smaller faces. A 1 inch projection is practical around adjacent doors, because it lets the pull clear neighboring fronts without extending too far into work aisles.
The precise 3-3/4 inch (96 mm) center to center spacing on the PA0221-SN satin nickel pull allows installers to set up drilling jigs or templates, which speeds production work on larger cabinet banks. That fixed spacing also helps on replacements where existing holes match the 96 mm pattern, reducing layout steps during change-outs. The 1/2 inch width gives a clear visual reference along the cabinet rail or stile, helping align the pull parallel to edges for a clean sightline. With a 1 inch projection, each pull stands off the face at the same depth, which keeps finger clearance consistent across doors and drawers in a kitchen run. The zinc die cast body helps the pull resist flex under hand load, which supports long-term alignment of the hardware once installed on the cabinet fronts.
The Hickory Hardware Metropolis pull has a 3-3/4 inch (96 mm) center to center size, which sets the screw hole spacing for drilling or aligning with existing cabinet holes.
The PA0221-SN satin nickel pull measures 4-3/4 inches in overall length, giving a balanced footprint across many standard cabinet drawer and door widths.
This 96mm cabinet pull has a 1 inch projection, so it stands off the cabinet face enough for finger clearance while staying relatively low profile.
The Metropolis series pull is made from zinc die cast material, providing a solid handle body for regular cabinet door and drawer use.
This Belwith Keeler cabinet pull uses a satin nickel finish, which offers a soft metallic look that coordinates with other satin nickel cabinet hardware.
The PA0221-SN pull belongs to the Metropolis collection from Hickory Hardware, helping maintain a consistent style across matching cabinet hardware.
The Hickory Hardware Metropolis pull with 3-3/4 inch (96 mm) center to center sizing, 4-3/4 inch length, and 1 inch projection gives clear dimensions for planning cabinet layouts. The zinc die cast construction and satin nickel finish support a unified look on projects using Belwith Keeler decorative handles and pulls. For work that relies on repeatable spacing and a consistent modern profile, this PA0221-SN satin nickel pull offers fixed measurements that translate directly into straightforward installation and a coordinated final appearance.