Drawer Bumper, Natural

Drawer Bumper White 10 Pack For Drawer Impact

drawer bumper white 10 pack from Fastcap is a door and drawer bumper designed to protect doors from being unintentionally marred from drawer pull-outs, helping cabinetry stay presentable during everyday use. The bumper is part of the door and drawer bumpers category, so it is purpose-built for this type of impact point. Part dimensions are 0.5 inches wide, 1.25 inches long, and 0.75 inches high, which creates a predictable stop point between the drawer and the door. This defined size supports consistent layout when multiple cabinets use the same part. The product is described as a Drawer Bumper, Natural and also as white in the SAP description, which helps identify the correct finish reference when ordering. The bumper is classified under work surface and tables bumpers, which aligns it with typical cabinet and shop furniture applications.

Key Drawer Bumper Details For Daily Use

• This Fastcap drawer bumper protects doors from being unintentionally marred from drawer pull-outs, which helps reduce visible damage at the meeting point between door and drawer fronts over time.
• The part dimensions of 0.5 inches wide, 1.25 inches long, and 0.75 inches high create a defined physical stop, so installers can plan consistent spacing when repeating the same detail across multiple cabinet openings.
• Drawer clearance of 0.5 inches on the sides and 0.375 inches in the front is required, giving a clear numeric target when laying out drawer boxes and face frames for proper bumper function.
• The bumper can be applied with PSA backing, or screwed in, or both, so installers can match the attachment method to the cabinet material and service expectations on site.
• The product is sold in full box quantities only, which suits project work where multiple cabinets or drawers need the same door and drawer bumper solution installed together.

Installation Clearances And Mounting Options

This Fastcap drawer bumper uses supplied PSA backing as one mounting option, which supports fast placement on job sites where drilling is less desirable. The bumper can also be screwed in, or both PSA and screws can be used together, which provides a mechanical hold when cabinets see heavier use. Drawer clearance of 0.5 inches on the sides is needed, so the bumper can sit in line with the drawer travel without rubbing the drawer box itself. The specified 0.375 inches of clearance in the front allows the bumper to act as the contact point before the door surface meets the drawer front. With part dimensions of 0.5 inches wide, 1.25 inches long, and 0.75 inches high, installers can pre-mark locations and drill points where screw mounting is preferred.

Using This Fastcap Drawer Bumper In Work

Where This Drawer Clearance Bumper Fits Best

This Fastcap drawer bumper is classified as a door and drawer bumper under work surface and tables, so it suits woodworking projects with doors in front of pull-out drawers. The stated role is to protect doors from being unintentionally marred from drawer pull-outs, which is common in face-frame or similar cabinet layouts where a door overlaps a sliding interior box. The part dimensions of 0.5 inches wide by 1.25 inches long by 0.75 inches high give the bumper enough presence to catch the drawer before it contacts the door, while staying compact enough for typical cabinet rails or stiles. Drawer clearance of 0.5 inches on the sides supports use beside standard drawer boxes without interference. The 0.375 inch clearance in the front supports layouts where the drawer needs a small setback behind the door plane so the bumper, rather than wood edges, absorbs the impact.

Details That Support Repeatable Cabinet Results

The clearly stated drawer clearance requirements of 0.5 inches on the sides and 0.375 inches in the front let installers design openings so the bumper operates consistently across a run of cabinets. Knowing the bumper measures 0.5 inches wide, 1.25 inches long, and 0.75 inches high allows accurate placement on rails, stretchers, or side panels before any mounting holes are drilled. Because the part can be applied with PSA backing or screwed in, or both, the same bumper can be used in different cabinet materials while keeping hardware uniform across a project. The identification as Drawer Bumper, Natural and the SAP description noting white in a 10 pack simplify reordering the exact same component when matching previous work. Being categorized as a door and drawer bumper in the work surface and tables group ties it directly to shop furniture, kitchen cabinets, or similar installations where drawers sit behind doors.

Common Questions About This Fastcap Drawer Bumper

Selecting This Drawer Bumper For Your Project

This Fastcap drawer bumper, described as Drawer Bumper, Natural and SAP-described as white in a 10 pack, offers a defined way to protect doors from drawer pull-outs. With 0.5 inch side clearance, 0.375 inch front clearance, and dimensions of 0.5 by 1.25 by 0.75 inches, it gives clear layout numbers for cabinet work. Mounting options using PSA backing, screws, or both support different cabinet materials and service levels across a project.