Berenson Forte Series Verona Bronze 18" (457 mm) Center to Center Appliance Pull, -8298-1VB-P

Berenson Forte Appliance Pull For Large Fronts

Berenson Forte appliance pull gives you a sturdy 18 inch center to center grip for appliance panels or large cabinet doors, so wide fronts can be opened with a comfortable, balanced handhold. The zinc die cast material creates a solid-feeling pull that supports everyday use on busy kitchen fronts. The Verona Bronze finish provides a darker, traditional tone that helps this pull coordinate with warm cabinet finishes in built-in appliance layouts. A 19 inch overall length spreads the load across more of the panel face, which helps distribute pulling force on tall or heavy doors. The 2-1/2 inch projection keeps hands clear of door faces, which is useful on thicker appliance panels. A 1-1/8 inch width offers a broad gripping surface, giving installers and users a stable edge to pull without feeling sharp transitions.

Key Forte Verona Bronze Pull Details

• The 18 inch center to center drilling provides a long mounting span that suits appliance fronts or oversized cabinet doors, so holes can be aligned with tall panels and extended rail sections.
• The 19 inch overall length slightly overhangs the 18 inch mounting centers, which frames the fastener points and gives added visual presence across wide fronts.
• The Verona Bronze finish keeps a consistent dark tone across the pull, helping it visually tie into bronze hinges or other dark decorative hardware on the same run.
• The zinc die cast construction creates a unified pull body, which supports a solid feel when operating heavy doors in high-use kitchen environments.
• The 2-1/2 inch projection establishes a stable hand clearance off the face, which helps users grip without contacting raised door profiles or panel edges during operation.
• The 1 inch base dimension at each end defines a compact footprint, allowing the pull to land cleanly on stiles or rail sections without crowding nearby edges.

Installation Fit For 18 Inch Center Spacing

The 18 inch center to center measurement sets the drilling layout, so installers can mark and bore two mounting points on appliance panels or cabinet doors with predictable spacing. The 19 inch overall length then positions the pull beyond those holes, so end pads sit slightly wider than the fasteners for a balanced look. A 1 inch base at each mounting end defines how much flat surface is needed, helping the pull seat securely on stiles or rails without overhanging narrow frames. The 2-1/2 inch projection plays into handle clearance, keeping knuckles away from door edges when the pull is mounted on thicker panels or profiled faces. With a 1-1/8 inch width, the gripping area remains substantial, which helps users grab the handle from different angles on tall or side-swing appliance fronts.

Using This Forte Appliance Pull On Projects

Where The Verona Bronze Pull Works Best

This Forte Verona Bronze appliance pull is suited to appliance panel installations or large cabinet doors that match its 18 inch center to center requirement, giving those fronts a long, continuous grip. The Verona Bronze finish coordinates with other dark-toned decorative hardware, which supports consistent hardware runs across kitchens using bronze hinges or handles. With a 19 inch overall length, the pull visually scales with tall or wide fronts, so the handle does not get lost on large panels. The 1 inch base dimension pairs well with standard stile widths, allowing the pull to sit fully on the flat area of a frame. Its zinc die cast construction means the body is formed as a strong, unified piece, so the handle can be placed where steady daily operation is expected on frequently used doors.

Details That Support Consistent Handle Results

The clearly defined 18 inch center to center spacing on this pull helps installers repeat hole locations across multiple doors, which is useful when laying out a bank of panels that need uniform alignment. The 19 inch overall length sets a known margin beyond the drilling points, giving a consistent reveal at each end along a cabinet run. With the 2-1/2 inch projection, the pull stands off the surface at a predictable distance, which supports planning around adjacent doors or trim that sit close by. The 1-1/8 inch width offers a stable grip area across the front, helping users get a firm hold even on heavy appliance doors. The zinc die cast material helps the pull maintain its form under frequent pulling cycles, which supports long-term alignment of the mounting points. The Verona Bronze finish offers a uniform color field along the handle, which helps installers match visual lines when aligning multiple pulls at the same height.

Common Questions About This Appliance Pull

Selecting This Forte Pull For Your Project

The Berenson Forte appliance pull pairs its 18 inch center to center layout with a 19 inch overall length, giving appliance fronts and large cabinet doors a proportional handle span. The Verona Bronze finish and zinc die cast construction support a solid, traditional appearance that aligns with many kitchen hardware lines. With a 2-1/2 inch projection, 1-1/8 inch width, and 1 inch base dimensions, this pull offers defined mounting and gripping geometry. For projects calling for a long appliance-style handle in a Verona Bronze finish, this Forte Series pull delivers a consistent set of dimensions to build your layout around.