
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
Berenson Forte appliance pull provides a substantial handle for appliance or large cabinet fronts where a longer grip is needed. This pull is part of the Toccata Series, so it follows a coordinated design family for projects built around that collection. The pull is made from zinc die cast, which creates a solid-feeling handle while supporting consistent dimensions from piece to piece. An oil rubbed bronze finish defines the visible surface, so the pull presents a dark, traditional look on the face of an appliance panel or tall door. The pull has a center to center dimension of 18 inches, which sets the spacing between mounting holes when laying out the front drilling pattern. A total length of 19 inches means the pull extends slightly beyond the hole centers at both ends, which affects how it visually fills wider panels.
The 18 inch center to center measurement controls drilling layout, because the mounting holes on the panel must be spaced to that dimension for the pull to seat correctly. A 2-1/2 inch projection places the handle forward from the panel face, which affects how easily hands can wrap behind the pull when installed on thicker appliance panels or oversized doors. The 1-1/8 inch width and 1 inch base diameter define how much of the hardware shows on the front, which matters when aligning the pull with door stile widths or appliance panel trim elements. The pull uses 10-24 x 3/4 inch screws, so the mounting interface is set up for that machine screw size and length when fastening through the panel.
This pull is classified as an appliance pull, which signals use on appliance panels or large cabinet applications rather than small doors. The 18 inch center to center spread suits wide refrigerator or freezer panels, because the handle spans a broader section of the face. A 19 inch overall length also aligns with the scale of tall pantry doors, so one pull can serve across both appliance fronts and tall cabinet runs. The oil rubbed bronze finish supports design schemes built around darker metal tones, letting the pull visually tie together appliances and adjacent cabinetry that share this finish. The Toccata Series designation places this pull within a collection, which helps when matching other handles or knobs specified from the same series for surrounding doors and drawers.
The zinc die cast material supports repeatable manufacturing, which helps the 18 inch center to center dimension stay consistent between pulls when multiple units are lined up on a long run. Consistent spacing supports straight visual lines across pairs of appliance doors or banks of tall cabinets using the same part. The 2-1/2 inch projection establishes a predictable standoff from the panel, which allows planning for door swing clearance near adjacent surfaces based on that fixed projection. A 1 inch base diameter at each end defines a round contact area that sits flat against the surface, which helps the pull register evenly when tightened down. The 1-1/8 inch width keeps the front bar proportionate to its length, so the grip feels aligned with the visual mass of the pull and the overall appliance or cabinet scale. The specified 10-24 x 3/4 inch screw size sets the thread and length used at installation, which lets fabricators drill for that fastener style when preparing panel backs.
The Berenson Forte appliance pull has an 18 inch center to center dimension, which sets the spacing for the two mounting holes drilled through the appliance panel or cabinet door.
The pull has a total length of 19 inches, so it extends beyond the 18 inch mounting hole spread and visually suits wider or taller appliance and cabinet fronts.
The appliance pull is made from zinc die cast, which creates a solid metal component with consistent dimensions suited to repeat installations in a project.
The pull has a projection of 2-1/2 inches, which sets how far it stands off the panel and provides finger clearance behind the bar when gripping.
The pull uses 10-24 x 3/4 inch screws, so the mounting holes can be prepared for that machine screw size when fastening through panels or doors.
The 8299-1ORB-P pull has an oil rubbed bronze finish, giving the visible surfaces a dark, rubbed appearance suited to traditional-style hardware layouts.
The Berenson Forte appliance pull in oil rubbed bronze brings an 18 inch center to center layout and 19 inch length to appliance and large cabinet fronts. With zinc die cast construction, defined projection, and Toccata Series styling, this pull offers a consistent mounting pattern and finish match across panels. When a project calls for a long, oil rubbed bronze handle on appliance fronts or tall doors, this model provides fixed dimensions that support repeatable layouts and coordinated appearance.
Sold In: 1 Each