Berenson Virtuoso Series 3-3/4" (96 mm) Center to Center Satin Nickel Pull, - 7131-1015-C

Virtuoso Pull 96mm Satin Nickel For Cabinets

Virtuoso pull 96mm satin nickel identifies this Berenson Virtuoso Series cabinet pull as a 3-3/4 inch (96 mm) center to center handle, giving installers a clear fit reference when laying out drill patterns on cabinet doors or drawers. The zinc die cast material provides a solid-feeling pull, supporting everyday cabinet use in busy kitchens, baths, or work areas. The satin nickel finish gives a muted metallic look, helping this pull coordinate with other satin nickel decorative hardware on the same run. A total length of 5 inches lets the hand grip extend past the screw centers, which aids comfortable finger clearance when opening heavier fronts. A base diameter of 3/8 inch defines the footprint at each mounting point, which matters when aligning over existing holes or working near narrow frame rails.

Key Berenson Virtuoso Pull Job Advantages

• The 3-3/4 inch (96 mm) center to center dimension sets an exact drilling distance, helping installers match standard cabinet boring patterns or replace existing 96 mm pulls without layout guesswork.
• The satin nickel finish delivers a consistent low-sheen metal surface, which suits contemporary cabinet runs where glare control and finish uniformity across multiple pulls are important.
• The zinc die cast construction creates a rigid pull body, helping the handle resist flex during repeated use on drawers and doors in high-traffic areas.
• The 5 inch overall length gives extra grip area beyond the mounting points, which is useful when users pull from an edge or with larger hands.
• The 15/16 inch projection sets the stand-off from the cabinet face, providing finger clearance behind the pull while helping avoid snagging on nearby surfaces.
• The 5/8 inch width defines a slender front profile, which supports clean sightlines on modern cabinets while still giving a defined surface to grasp.

Mounting And Fit Details For 96 mm Pull

The 96 mm center to center layout fixes the hole spacing for this pull, so installers can bore two straight-through holes at that distance and know the handle will seat correctly. The 3/8 inch base diameter at each end helps cover cleanly drilled holes while keeping the contact area compact on narrow rails or stile edges. With a 15/16 inch projection, the pull stands off just under an inch from the face, giving working room for fingers behind the handle when pulling doors or drawers. The 5 inch overall length and 5/8 inch width combine to create a balanced footprint, which matters when aligning multiple pulls in a row so sightlines stay consistent.

Using This Berenson Virtuoso Series Pull In Projects

Where The Berenson Virtuoso Cabinet Pull Fits Best

This Berenson Virtuoso Series zinc die cast pull with satin nickel finish fits cabinet and drawer applications that are bored on a 3-3/4 inch (96 mm) center to center pattern, giving a straightforward match to that standard spacing. The 5 inch overall length works well across both base cabinet doors and wider drawer fronts, so the same pull can carry through a full room layout. Its 5/8 inch width keeps the handle visually light, which suits face frame or frameless cabinets that use narrow rails, while still offering a defined gripping surface. The 15/16 inch projection supports finger access without pushing the handle excessively far into the aisle, which is useful on cabinets installed along walkways or in tighter galley spaces. The satin nickel finish helps coordinate with other satin nickel decorative hardware and hinges, supporting consistent finish choices throughout a project. The zinc die cast body gives this handle a solid feel in hand, which is valuable where drawers carry everyday loads and doors are opened frequently.

Details That Support Consistent Cabinet Hardware Results

The clearly specified 96 mm center to center distance on this pull allows installers to use standard jigs or boring templates, which speeds repetitive drilling and keeps hardware rows visually aligned. A base diameter of 3/8 inch at each mounting point defines the bearing surface on the door or drawer, helping the pull seat squarely against the face for a tidy finish. With a projection of 15/16 inch, the handle creates a predictable offset from the surface, reducing variation when matching this pull across multiple cabinet banks. The 5 inch overall length gives installers a consistent reference when positioning pulls relative to door edges or drawer top rails, which supports symmetrical layouts. The 5/8 inch width provides a repeatable visible band of metal on the front, helping sightlines stay uniform from one cabinet front to the next. The satin nickel finish and zinc die cast construction together provide a stable, uniform appearance across a group of pulls, which matters on longer cabinet runs where small differences become noticeable.

Common Questions About The Virtuoso Satin Nickel Pull

Select This 96 mm Satin Nickel Pull For Your Next Run

The Berenson Virtuoso Series 3-3/4 inch (96 mm) center to center satin nickel pull pairs a defined 96 mm hole spacing with a 5 inch zinc die cast body, giving installers a clear drilling reference and a solid-feeling handle. Its 5/8 inch width and 15/16 inch projection provide practical grip comfort while maintaining clean cabinet sightlines. For cabinet and drawer fronts set on a 3-3/4 inch pattern, this 7131-1015-C pull from Wurth Baer Supply offers a straightforward way to bring a consistent satin nickel look across an entire project.