Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Berenson Opus Series pull gives you a 5-1/16 inch (128 mm) center to center handle that positions fastener holes at a consistent spacing, which supports straightforward layout across doors and drawers. The Opus pull is part of the Opulence Series, so it follows a coordinated design line, which helps keep a uniform look when you repeat it through a room. Its Verona Bronze finish defines the visual tone of the pull, so it can set a warm metal accent against cabinet finishes. The pull is made from zinc die cast material, which provides a solid metal body that installs firmly on typical cabinet fronts. Overall length of 6-3/8 inches gives you extra bar beyond the mounting holes, which provides finger clearance when gripping the handle.
The 5-1/16 inch (128 mm) center to center measurement on this Opus pull controls where holes land in the cabinet face, which is important when laying out new fronts or aligning with existing boring patterns. An overall length of 6-3/8 inches means the pull extends beyond those mounting points, which gives more finger surface to grab. A projection of 1-1/4 inches defines the standoff from the door or drawer, which matters when planning for hand clearance near adjacent edges or trim. The pull width of 13/16 inch sets the visible bar size, which plays into both ergonomics and appearance on narrow and wide fronts.
This Opus pull with 5-1/16 inch (128 mm) center to center spacing fits cabinet and drawer layouts built around that metric or imperial hole pattern, which helps maintain consistency across a run of fronts. The Verona Bronze finish lets the pull act as a distinct metal accent, which can frame doors and drawers on kitchen, bath, or shop cabinetry. With an overall length of 6-3/8 inches, the handle scales well on medium-width doors and wider drawers, which helps the hardware look proportionate rather than undersized. A base diameter of 11/16 inch defines the footprint at each contact point, which affects how the pull transitions into the door surface and how it reads visually on stile-and-rail or flat-panel designs.
The defined 5-1/16 inch (128 mm) center to center dimension on the Berenson Opus Series pull supports jig-based drilling, which helps installers repeat the same hole spacing cleanly across multiple cabinet fronts. Using a consistent 6-3/8 inch overall length means each handle lands at the same visual width, which helps align sightlines on banks of drawers. The 1-1/4 inch projection stabilizes how far pulls extend from the face, which keeps hand clearance uniform from cabinet to cabinet. A 13/16 inch width keeps the grip profile consistent, which aids muscle memory when opening doors and drawers. The M4 x 45mm screw size specification defines the thread and length pairing for this pull, which matters when matching to the pre-bored hole size and material thickness during install.
The Berenson Opus Series pull has a 5-1/16 inch (128 mm) center to center dimension, so hole spacing matches layouts using that common cabinet and drawer pattern.
The 7154-10VB-P pull measures 6-3/8 inches in overall length, giving extra handle beyond the mounting points for an easier grip on doors and drawers.
The Opus pull is made from zinc die cast, providing a solid metal body that works well for typical cabinet door and drawer applications.
This Opulence Series pull uses a Verona Bronze finish, setting a defined bronze tone that can coordinate with surrounding cabinet finishes and fixtures.
The Opus pull has a 1-1/4 inch projection, establishing the standoff distance that affects finger and knuckle clearance during regular use.
The Berenson Opus Series pull uses M4 x 45mm screws, which defines both the thread and installed depth range for typical cabinet door and drawer thicknesses.
This Verona Bronze cabinet pull combines a 5-1/16 inch (128 mm) center to center dimension with a 6-3/8 inch overall length, giving you a repeatable layout and full-size grip across doors and drawers. With zinc die cast construction and a defined 1-1/4 inch projection, it delivers a consistent feel and clearance on cabinets set up around the 128 mm pattern. For projects calling for Opulence Series styling in Verona Bronze, this pull lines up the key sizes and finish details for a unified hardware run.
