Berenson Maestro Series 3-3/4" (95 mm) Center to Center Satin Nickel Pull, - 7174-1015-C

Berenson Maestro Satin Nickel Pull For Cabinets

Berenson Maestro satin nickel pull describes a zinc die cast cabinet handle from the Maestro collection that is finished in satin nickel, so it gives cabinet doors and drawers a consistent visual line that matches other Maestro pieces in the same finish. The pull has a center to center measurement of 3-3/4 inches, also listed as 96mm, which sets the drilling pattern for the installer and keeps replacement or new layouts predictable across multiple fronts. Overall length is 4-1/2 inches, so the handle extends slightly beyond the hole spacing, which leaves a defined gripping area for fingers while keeping the profile compact on narrower rails. A projection of 1-1/16 inches sets how far the pull stands off the face, giving space for a secure grip while holding the handle close to the cabinet to limit snag points along runouts. The 7/16 inch width and 1/2 inch base diameter concentrate the design into a narrow footprint, which matters when laying out pulls on tight stile widths.

Key Maestro Cabinet Pull Details For Projects

• The Maestro collection identity ties this pull to the broader Berenson Maestro Series, which matters when matching new hardware to existing installations or planning a coordinated hardware schedule across a room or project.
• Zinc die cast material defines the core of the pull, providing a rigid metal body that supports daily opening and closing loads while keeping the handle profile precisely formed along its length.
• The satin nickel finish on the pull surface creates a muted metallic appearance that helps fingerprints blend visually and supports a consistent look alongside other satin nickel decorative hardware.
• A 3-3/4 inch, or 96mm, center to center dimension sets exact hole spacing, which is critical when drilling new fronts or swapping hardware on pre-bored doors and drawers.
• The 4-1/2 inch overall length gives installers a sense of the visual footprint on the face of the cabinet, helping with proportion choices on different drawer widths and door heights.
• A projection of 1-1/16 inches defines how far the pull stands off the surface, providing finger clearance that supports comfortable gripping without pushing the handle too far into the work area.

Installation Geometry And Mounting Fit Details

The 3-3/4 inch center to center dimension on this Berenson Maestro Series pull establishes the two mounting points, so hole drilling for new work or retrofits follows a clear 96mm pattern. The specified M4 x 45mm screw size matches the pull threading, which sets the interface between the pull and the door or drawer front and guides hardware selection for various front thicknesses. With a base diameter of 1/2 inch, the contact area around each mounting point is defined, which spreads load modestly around the holes and shapes how the pull seats against the surface. The 7/16 inch width across the grip keeps the handle slim, which influences layout when multiple pulls are placed near each other on smaller fronts. The 1-1/16 inch projection controls how much the pull stands off the cabinet face, so installers can anticipate clearance relative to adjacent doors, trim pieces, or nearby hardware lines.

Using This Maestro Pull In Cabinet Projects

Where This Satin Nickel Maestro Pull Fits Best

This Berenson Maestro Series pull belongs to the Decorative Hardware & Moldings, Handles and Pulls category, so it is built for cabinet doors and drawers where a metal handle is required. The 3-3/4 inch, or 96mm, center to center measurement suits layouts based on common metric or imperial drilling jigs, which helps when standardizing hardware across a bank of cabinets or a full room. An overall length of 4-1/2 inches provides a compact visual scale, so the pull works on narrow doors as well as smaller drawers without overwhelming the front. The 7/16 inch width and 1/2 inch base diameter keep its footprint modest, which is useful when stiles or rails are tight and space for hardware is limited. Satin nickel finish pairs with many contemporary and transitional cabinet finishes, so this pull can be specified where a soft metallic tone is part of the design plan.

Details That Support Repeatable Cabinet Hardware Results

The 96mm center to center spacing on this Maestro collection cabinet pull provides a fixed drilling dimension, which supports repeatable results when using templates or CNC drilling patterns across multiple fronts. The 1-1/16 inch projection sets consistent stand-off from the cabinet face, so the feel of the grip remains the same from door to door, supporting uniform user experience in kitchens or casework runs. Zinc die cast construction maintains the shape of the pull under regular hand force, helping the handle stay aligned with the drilled holes over time. The satin nickel finish contributes a controlled sheen level across every pull, which matters when rows of cabinets catch light from various angles. The M4 x 45mm screw specification defines a known machine thread engagement into the pull, helping installers coordinate fastener length to their front thicknesses while maintaining a secure mechanical connection. The defined 4-1/2 inch length makes spacing from panel edges and neighboring hardware more predictable, which is useful when aligning multiple pulls or planning hardware reveals.

Common Questions About This Berenson Maestro Pull

Selecting This Maestro Pull For Your Next Job

This Berenson Maestro Series 3-3/4 inch center to center satin nickel pull combines zinc die cast construction, a 4-1/2 inch overall length, and a 1-1/16 inch projection, giving cabinet and millwork projects a defined drilling pattern and consistent grip profile. With its Maestro collection identity, satin nickel finish, and 96mm mounting dimension, it suits hardware schedules that call for coordinated decorative pulls across multiple fronts. For projects needing a compact, metal cabinet handle with known measurements and M4 x 45mm screw specification, this 7174-1015-C pull provides clear geometry for layout and installation on doors and drawers.