
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
Berenson Maestro pull 96mm describes a Maestro Series cabinet pull from Berenson Corporation that is built as a zinc die cast handle in a Verona Bronze finish, so it delivers a defined metal shape with a consistent, project-ready color across your run of doors or drawers. The 3-3/4 inch (95 mm) center to center mounting dimension sets fixed hole spacing, which helps keep drilling layouts repeatable across multiple fronts. Overall length of 4-1/2 inches gives you extra grip area beyond the mounting points, which matters when you are working on wider drawer fronts. A projection of 1-1/16 inches offsets the hand from the face, creating finger clearance that supports comfortable, everyday use. With a width of 7/16 inch, the pull keeps a slim footprint, which helps when you are working with narrow rails or tight layout lines.
This Berenson Maestro Series cabinet pull uses a 3-3/4 inch (95 mm) center to center dimension, so hole placement on doors and drawers is driven by that fixed spacing for consistent alignment across the run. The pull is matched to M4 x 45mm screws, establishing the thread size and basic length relationship between the pull and the cabinet front. With an overall length of 4-1/2 inches, the pull extends slightly beyond the mounting centers, which helps position the grip where it feels natural on standard drawer fronts. A 1/2 inch base diameter at each end defines how much surface area sits against the cabinet face, which is useful when planning reveals and edge distances.
This Berenson Maestro Series pull is a zinc die cast handle in a Verona Bronze finish, so it works wherever that metal look and tone is part of the cabinet design, from kitchen doors to shop storage fronts that call for consistent hardware. The 3-3/4 inch (95 mm) center to center spacing lines up with a common cabinet drilling standard, which lets you apply the same pattern across multiple cabinets and drawers without changing your layout approach between pieces. Overall length of 4-1/2 inches gives this pull enough span for typical cabinet and drawer widths, making it practical for both upper doors and base cabinet drawers that need a reliable handhold. With a projection of 1-1/16 inches and width of 7/16 inch, the pull provides finger clearance while still sitting close to the face, which is helpful on cabinets near walkways where low-profile hardware is preferred.
The 3-3/4 inch (95 mm) center to center specification on this Maestro pull defines the exact distance between mounting points, which streamlines jig setup when you want repeatable hardware placement across a full bank of fronts. Matching M4 x 45mm screw sizing to the pull establishes a standard metric thread, which keeps hardware selection straightforward when working with cabinet doors and drawers drilled for that screw format. A 1/2 inch base diameter at each end sets a clear bearing surface against the door or drawer, which can visually mask the immediate drilled area and contribute to a clean finished look. Because the pull is part of the Maestro Collection from Berenson Corporation, its profile and Verona Bronze finish align with other Maestro pieces, which supports visually consistent results when the job calls for coordinated cabinet hardware through the entire room.
This Maestro Series pull has a 3-3/4 inch (95 mm) center to center dimension, so hole spacing on the cabinet front follows that measurement for accurate alignment.
The Berenson 7177-10VB-P Maestro pull has an overall length of 4-1/2 inches, which provides additional grip area beyond the 3-3/4 inch mounting centers.
This pull is made from zinc die cast material with a Verona Bronze finish, combining solid metal construction with a coordinated bronze appearance for matching cabinet hardware.
The Maestro pull has a projection of 1-1/16 inches, setting the grip away from the cabinet surface to provide finger clearance during everyday use.
This Berenson cabinet pull is matched to M4 x 45mm screws, defining the thread size and basic length relationship between the pull and the cabinet front.
The Maestro pull has a width of 7/16 inch and a base diameter of 1/2 inch, which sets a slim visible profile while covering the immediate mounting area on the door or drawer.
The Berenson Maestro Series 3-3/4 inch (95 mm) center to center pull in Verona Bronze combines zinc die cast construction, a 4-1/2 inch overall length, and 1-1/16 inch projection, giving you a compact, repeatable hardware choice for cabinet doors and drawers across your next project.
Sold In: 1 Each