Berenson Advantage Series 3" (76 mm) Center to Center Brushed Nickel Pull, - 0924-1BPN-P

Berenson Advantage Series Pull For Cabinets

Berenson Advantage Series pull gives a straightforward 3 inch center to center grip that lines up with common cabinet drilling, which keeps change-outs and new layouts predictable on doors and drawers. The pull is made from zinc die cast material, so the body provides a solid metal feel that suits everyday cabinet use. A brushed nickel finish on the pull presents a muted metal look, which helps it sit well with many brushed nickel hinges and other visible hardware. Overall length is 5-1/4 inches, so the pull spans past the screw locations to offer a comfortable handhold. A projection of 1 inch sets the handle off the surface, which leaves space for fingers to wrap without rubbing face frames. Width is 1/2 inch, so the profile stays slim where space between fronts is limited.

Key Details That Shape Daily Cabinet Use

• The 3 inch center to center dimension matches a widely used drilling pattern, which simplifies aligning this pull with existing 3 inch hole spacing on cabinet doors and drawer fronts.
• The 5-1/4 inch overall length stretches beyond the fastener line, which provides more grasp area for opening heavier drawers or wider doors without crowding the hand near the mounting points.
• The 1 inch projection sets the pull away from the surface, which allows fingers to hook behind the bar so users can pull straight out without scraping knuckles on the cabinet face.
• The 1/2 inch width creates a narrow front profile, which is useful where doors and drawers sit close together and where a lower profile handle reduces the chance of adjacent fronts clashing.
• The 5/8 inch base diameter at each end spreads the load at the contact point, which helps seat the pull firmly on the surface and creates a defined footing against the cabinet finish.
• The 8-32 x 1 inch screw size is a standard cabinet thread and length, which supports straightforward fastening into typical cabinet door and drawer front thicknesses.

Installation Dimensions For Cabinet Fit

This Berenson Corporation pull uses a 3 inch center to center spacing, which lets installers align drill points on a consistent grid across multiple fronts. The 5/8 inch base diameter at each end gives a clear footprint, which helps position the pull square to door edges or drawer tops. A 1 inch projection sets a fixed stand-off, which influences how far the handle sits from adjacent walls or overlapping fronts. Width at 1/2 inch defines the narrow face of the pull, which matters when planning layouts with tight reveals. The 8-32 x 1 inch screw size specification identifies a common thread and length, which fits standard cabinet construction depths in many shop and site conditions.

How This Brushed Nickel Pull Works In Practice

Where This 3 Inch Center Pull Fits Best

The 3 inch center to center layout places this pull in a common cabinet size range, which suits many kitchen, bath, or shop fronts built around that spacing. Its 5-1/4 inch overall length reaches beyond the holes, which gives more visual coverage across typical rail widths and offers a steady grab point even on medium-width drawers. Made from zinc die cast material, the pull provides a single-piece metal construction, which supports regular opening and closing cycles on frequently used doors. The brushed nickel finish delivers a soft metallic appearance, which pairs with other brushed nickel decorative hardware and moldings to keep a consistent hardware look across a run of cabinets.

Details That Support Consistent Alignment And Use

The 5/8 inch base diameter at both ends defines a circular contact patch, which helps pulls sit evenly over drilled holes and creates a clean transition onto painted or stained faces. A 1 inch projection from the surface fixes the reach distance, which reduces variation from cabinet to cabinet and keeps enough space for fingers without pushing the handle excessively into walkways. With a 1/2 inch width, the pull keeps its front edge narrow, which can reduce visual bulk on smaller drawer fronts while still presenting a clear pull point. The specified 8-32 x 1 inch screw size ties directly to a widely used machine screw standard, which supports a straightforward mounting approach across many cabinet carcass materials. Combined, these dimensions from the Advantage Series collection create a repeatable layout, which helps runs of doors and drawers read uniformly once installed.

Common Questions About This Berenson Advantage Pull

Choose This Pull For 3 Inch Cabinet Layouts

This brushed nickel Berenson Advantage Series pull combines a 3 inch center to center layout with a 5-1/4 inch length, which suits many cabinet runs set on that spacing. The zinc die cast construction and defined 1 inch projection give a consistent feel across doors and drawers. Using the specified 8-32 x 1 inch screw size and the 5/8 inch base footprint, this pull supports a straightforward layout on cabinet fronts where a brushed nickel finish and 3 inch center spacing are already part of the design.