Berenson Advantage One Series 3" (76 mm) Center to Center Oiled Bronze Pull, - 0948-1OB-P

Berenson Advantage One Pull For Cabinets

Berenson Advantage One pull is a zinc die cast handle in the Advantage Series with an oiled bronze finish, so it provides a coordinated decorative option for cabinets and drawers where this series is already specified. The 3 inch center to center drilling matches a common layout, which helps when aligning new fronts to existing hole patterns in typical cabinet runs. Overall length of 3-11/16 inches gives some overhang beyond the screw centers, offering a comfortable grip area without overwhelming standard door and drawer sizes. A projection of 1-3/16 inches stands the hand clear of the surface, which helps when opening heavier fronts. Width of 9/16 inch keeps the pull visually light while still giving enough edge for fingers to grab. A base diameter of 5/8 inch at each end gives a defined footprint against the face, helping the pull sit neatly on the cabinet surface.

Key Advantage Series Pull Details In Practice

• The 3 inch center to center dimension allows this pull to match a widely used drilling pattern, which is valuable when replacing existing hardware on cabinets that already have 3 inch hole spacing.
• The 3-11/16 inch overall length creates a balanced proportion around the mounting centers, which helps the pull look properly scaled on standard cabinet doors and smaller drawers.
• The oiled bronze finish defines the visual tone of the pull, which supports design choices where a warm, darker metal is desired across a kitchen, bath, or built-in project.
• The zinc die cast material provides a solid metal construction, which is important when a job calls for decorative hardware that still feels substantial in hand use.
• The 1-3/16 inch projection sets the pull out from the door or drawer face, which gives fingers room to grip from below or the side without scraping against the cabinet surface.
• The 9/16 inch width and 5/8 inch base diameter work together to form a narrow bar with defined mounting pads, which helps the pull register cleanly on the face of the cabinet.

Cabinet Pull Sizing And Hole Layout Details

The 3 inch center to center measurement on this Berenson Advantage One pull establishes the drilling pattern for installation, so the two mounting points line up with standard 3 inch cabinet hardware boring jigs. With a 3-11/16 inch overall length, the handle extends slightly past the screw locations, so there is metal to grab beyond the attachment points while keeping the mounting area compact. Projection of 1-3/16 inches defines how far the pull stands off the surface, which affects clearance when doors open near adjacent walls or appliances. The 9/16 inch width keeps the pull slim along its length, allowing it to sit neatly on narrow rails and drawer fronts. A 5/8 inch base diameter at each end creates a consistent landing area around each fastener point, helping the pull seat flush against flat cabinet faces.

Using This Oiled Bronze Pull In Real Projects

Where This Oiled Bronze Cabinet Pull Fits

This Berenson Advantage One Series pull, with its 3 inch center to center measurement, fits cabinet and drawer fronts drilled on a 3 inch pattern, which is common in many kitchen and bath layouts. The oiled bronze finish places it within projects that call for a darker, warmer metal tone, so it can tie together hinges and other visible hardware in a coordinated way. Overall length of 3-11/16 inches allows the pull to sit comfortably on doors and drawers of various widths, from narrow uppers to medium drawers, without visually dominating the front. The 9/16 inch width keeps the profile slim enough for tighter spaces, such as narrow face frames or smaller vanity drawers. A base diameter of 5/8 inch on each end offers a defined footprint that visually caps the bar, which helps the pull look intentional on both framed and frameless cabinet styles.

Details That Support Consistent Hardware Results

The 3 inch center to center drilling on this cabinet pull aligns with many standard templates, which helps maintain consistent spacing across multiple doors and drawers on a job. The 1-3/16 inch projection sets a predictable standoff from the cabinet face, so front clearances remain uniform across an installation. Zinc die cast construction gives a metal body that holds its shape around the mounting points, which supports stable fastening at each 5/8 inch diameter base. The 3-11/16 inch overall length and 9/16 inch width define a repeatable bar size, allowing installers to visually line up multiple pulls and keep sight lines straight. The oiled bronze finish keeps the appearance consistent from piece to piece, which matters when rows of pulls run across long cabinet banks and need to read as one coordinated set.

Common Questions About This Berenson Cabinet Pull

Selecting This Pull For Your Next Cabinet Run

The Berenson Advantage One pull, model 0948-1OB-P, combines a 3 inch center to center layout with an oiled bronze finish, so it fits projects built around that drilling pattern and color tone. With 3-11/16 inch overall length, 1-3/16 inch projection, 9/16 inch width, and 5/8 inch base diameter, its dimensions support consistent alignment across doors and drawers. For cabinet work that uses zinc die cast decorative hardware in the Advantage Series, this pull offers a defined, repeatable size and finish to carry through an entire run.