160mm Allison™ Value Hardware Handle Pull, Satin Nickel

160mm Allison Value Hardware Handle Pull For Cabinets

160mm Allison Value Hardware Handle Pull describes a cabinet handle from Amerock Corporation designed for projects needing a 6-5/16 inch, 160 mm center-to-center mount, so it suits layouts built around that standard drilling dimension. The handle belongs to Amerock's Blythe Collection, which uses a ribbed barrel center with decorative accents and smooth curved lines, giving traditional cabinetry a defined grip point and a consistent visual detail along a run of doors and drawers. The handle uses zinc die-cast construction, so the body provides a solid feel in hand while maintaining the precise decorative shapes called out in the Blythe design. A satin nickel finish covers the pull, so the surface presents a muted metallic look that coordinates with many hinges and decorative hardware while helping minor fingerprints and everyday use marks blend into the brushed tone.

Key Blythe Handle Details That Support Projects

• The Blythe Collection design with a ribbed barrel center and decorative accents creates a consistent traditional style across multiple doors, helping installers match existing classic profiles on cabinet banks.
• A zinc die-cast material body gives the handle a solid, unified construction, supporting repeated pulls on doors and drawers in busy kitchen or shop environments.
• The satin nickel finish provides a soft metallic surface that pairs with common satin nickel hinges and latches, simplifying finish coordination on full room hardware schedules.
• A length of 7-1/16 inches, or 179 mm, spans wider stile or drawer front faces, giving users a generous grip zone while keeping mounting points at the specified 160 mm spacing.
• A projection of 1-3/4 inches, or 44 mm, stands the handle off the cabinet face, giving fingers room behind the pull for comfortable everyday operation on doors and heavier drawers.
• A width of 13/16 inch, or 21 mm, balances a substantial handhold with refined lines, which helps the pull register visually without overpowering narrower cabinet rails.

Mounting Dimensions And Satin Nickel Fit Details

This Amerock Blythe handle uses a 6-5/16 inch, 160 mm center-to-center mounting dimension, so the screw holes line up with standard 160 mm drill patterns commonly used on European and frameless cabinetry layouts. The base diameter of 3/4 inch, or 19 mm, at each end of the pull defines the footprint against the door or drawer surface, which helps installers understand how the pull will sit relative to edge reveals and panel details. With a total length of 7-1/16 inches, the handle stretches beyond the mounting posts, giving a balanced extension beyond each screw location that looks proportional on wider drawers and tall doors.

Using The Amerock Blythe Pull In Real Projects

Where The 160mm Center-To-Center Pull Works Best

The Amerock Corporation BP55225G10 handle pull fits projects that use a 160 mm center-to-center layout, because its mounting holes are fixed at that spacing and align with pre-bored 160 mm rows. In kitchen, bath, or shop cabinets built on metric hardware grids, this 160 mm center dimension lets installers swap or upgrade existing handles on doors and drawers without altering the drilling pattern when that pattern already matches 160 mm. The satin nickel finish works on both painted and stained casework because the neutral metallic tone complements light and dark surfaces, helping hardware tie together mixed-material installations. The Blythe Collection styling, defined by a ribbed barrel center and decorative accents, suits traditional and transitional cabinets, allowing this pull to be used across upper doors, base doors, and drawer fronts while keeping a single visual theme.

Details That Support Consistent Mounting And Operation

The 7-1/16 inch overall length provides a known span that helps align the handle along rail edges and drawer faces, giving installers a repeatable reference when laying out centerlines and end clearances. A projection of 1-3/4 inches from the cabinet face sets the handle far enough out that fingers can wrap behind the ribbed barrel center, which supports firm, comfortable pulls on heavier drawers and taller pantry doors. The width of 13/16 inch offers a stable gripping surface, so the pull feels substantial during use while still fitting on narrower stiles without crowding panel profiles. With a base diameter of 3/4 inch at each post, the pull covers the drilled screw area cleanly, which is useful on finished faces where a neat transition between hardware and door surface is important. The zinc die-cast construction carries the Blythe ribbing and decorative accents accurately along the barrel, maintaining consistent appearance from piece to piece on long cabinet runs.

Common Questions About This Amerock Blythe Handle

Select This 160mm Pull For Satin Nickel Runs

The 160mm Allison Value Hardware Handle Pull in satin nickel from Amerock Corporation pairs a 6-5/16 inch, 160 mm center-to-center mount with Blythe Collection styling, giving cabinet projects a traditional ribbed barrel look that repeats cleanly across doors and drawers. With its zinc die-cast construction, 7-1/16 inch overall length, 1-3/4 inch projection, and 13/16 inch width, this handle defines how it will sit and feel on finished cabinetry, supporting consistent layouts on jobs that specify satin nickel decorative hardware.