Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Nylon Shelf Pins 5 mm Bore from Selby Furniture Hardware pair a nylon shelf pin with a matching hold down to support and lock cabinet shelves. The nylon shelf pin fits 5 mm diameter holes in 32 mm systems, so it drops directly into standard 32 mm line-bored cabinet sides. The hold down is inserted over the shelf and compresses to lock the shelf, so the shelf stays restrained during transport or use. The shelf pin is 5 mm diameter x 5/16 inch long, permitting insertion on both sides of material that is 5/8 inch thick or over, which lets you support a shelf from opposing cabinet sides on typical 5/8 inch panels. The white finish on the nylon shelf holder P103113W blends with light casework, helping hardware stay unobtrusive in finished installations.
This nylon shelf support set is built around a 5 mm diameter shelf pin that fits 5 mm diameter holes in 32 mm systems, so drilling patterns based on the 32 mm system align directly with the hardware. Because the shelf pin is 5 mm diameter x 5/16 inch long, it engages the panel without excessive projection, which helps the pin sit solidly while still allowing room for the shelf edge. The ability to insert the pin on both sides of material 5/8 inch thick or over means standard cabinet side thicknesses can be drilled and supported symmetrically, helping maintain level shelves across the cabinet width. The hold down component slides over the shelf and compresses to lock the shelf, so once the shelf is resting on the nylon pins, the hold down adds restraint against upward movement.
This Selby shelf support is specified as a nylon shelf pin that fits 5 mm diameter holes in 32 mm systems, so it is suited to cabinets laid out on a 32 mm drilling grid. When cabinet sides are bored with 5 mm holes on standard 32 mm centers, the 5 mm diameter pin drops into the bore without additional fitting, which supports efficient production or on-site drilling. The shelf pin measures 5 mm diameter x 5/16 inch long, so it occupies a short length of the bore while projecting enough to support the shelf edge along the cabinet side. Because the pin permits insertion on both sides of material 5/8 inch thick or over, cabinet builders using 5/8 inch or thicker side panels can place matching pins on opposing sides and know the support length suits that material thickness. This geometry helps keep shelf load shared evenly between left and right supports in typical frameless or casework builds.
The matching hold down is inserted over the shelf and compresses to lock the shelf, so once the shelf is sitting on the nylon pins, the hold down adds a clamping effect against the shelf surface. This compression helps the shelf stay seated on the pins when cabinets are moved, which aligns with the note that shelves may be installed before shipping. By combining a nylon shelf pin with a compressive hold down, the nylon shelf support for 32 mm system work both carries vertical load and restrains vertical lift, which is useful when shelves must remain fixed relative to the cabinet sides. The white nylon material of the shelf holder P103113W keeps the support visually low-profile against many painted or laminate interiors, which maintains a clean appearance while the mechanical functions of support and locking continue to operate.
The nylon shelf pin fits 5 mm diameter holes in 32 mm systems, so any properly drilled 5 mm bore on a 32 mm layout works with this holder.
The hold down is inserted over the shelf and compresses to lock the shelf, so the shelf is restrained against lifting off the nylon pins during normal use.
The shelf pin is 5 mm diameter x 5/16 inch long, permitting insertion on both sides of material 5/8 inch thick or over, which suits many cabinet side panels.
This nylon shelf support fits 5 mm diameter holes in 32 mm systems, aligning it with cabinets and casework laid out on a 32 mm drilling pattern.
The manufacturer part number is P103113W, so shops can match existing nylon shelf holders or specify this exact model in project documentation.
The nylon shelf holder is described as white, so it blends with many light-colored cabinet interiors while performing the support and hold-down functions.
The Selby Furniture Hardware P103113W nylon shelf holder uses a 5 mm diameter shelf pin sized for 5 mm diameter holes in 32 mm systems, so it fits neatly into standard line-bored cabinet sides. With a shelf pin measuring 5 mm diameter x 5/16 inch long, it permits insertion on both sides of material 5/8 inch thick or over, aligning with common cabinet panel thicknesses. The hold down is inserted over the shelf and compresses to lock the shelf, so shelves may be installed before shipping while remaining restrained. For projects that rely on nylon shelf pins 5 mm bore to support and secure adjustable shelves, this part provides a matched pin and compressive hold down tuned to 32 mm system drilling.
Sold In: 500 Each