Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Italian Designs Series zinc die cast pulls give cabinets a consistent, modern look by pairing a zinc die cast body with a smooth satin nickel finish, so runs of doors and drawers share the same visual line. The pull has a 5-3/8 inch length, which spreads the grip area across more of the drawer or door face and helps balance the hardware on wider fronts. A 5-1/16 inch center to center dimension sets clear drilling locations, helping layout stay accurate across multiple cabinets. The 7/8 inch projection keeps fingers clear of the cabinet surface while opening, which matters on heavier doors or when hands are wet or gloved. A 1/2 inch width offers a slimmer front profile, giving panels a cleaner appearance while still providing enough surface for a solid grip in daily use.
The 5-1/16 inch center to center measurement defines the distance between mounting holes, so jigs or templates can be set once and reused across all fronts. A total length of 5-3/8 inch means the pull slightly overhangs the hole spread, which leaves enough material at each end for a visually anchored look on the door or drawer. The 7/8 inch projection sets the pull off the cabinet face at a practical distance, giving space for fingers while keeping the handle tight to the panel line. With a 1/2 inch width across the front, the pull sits narrow on the face, which can help when spacing multiple pulls on banks of drawers. The combination of these fixed measurements supports consistent alignment across an entire run of cabinets.
The smooth satin nickel cabinet pull from Schaub and Company works well on cabinet doors or drawers where a contemporary metal finish is desired, because the satin surface reads clean without bright reflection. Its 5-3/8 inch length suits common kitchen and bath cabinet widths, so a single size can often be used across both wall and base units. The 5-1/16 inch center to center dimension aligns with a popular drilling size, which makes it practical for new installations and for updating cabinets already laid out to that spacing. The zinc die cast construction supports use on frequently accessed storage, such as kitchen drawers or laundry cabinets, where hardware is pulled multiple times a day. Within an Italian Design hardware layout, this pull can serve as the primary handle across a room, tying together doors, drawers, and utility cabinets.
The 5-1/16 inch center to center size allows installers to standardize drilling across a job, which reduces layout time and helps banked drawers align cleanly under countertops. Having a 5-3/8 inch overall length relative to that hole spacing leaves short end segments that frame the grip area, which keeps the pull looking proportional on mid-size fronts and reduces the chance of the handle appearing too short. The 7/8 inch projection creates just enough stand-off that fingers can wrap the pull without contacting the door surface, which helps protect finished cabinet faces over time. At 1/2 inch width, the pull presents a narrow line on the cabinet, which assists when aligning multiple pulls side by side on double doors or wide drawer banks. The zinc die cast body and smooth satin nickel finish combination also gives a consistent surface, which is useful when lining up several pulls under direct lighting where irregular profiles would be noticeable.
The pull has a 5-1/16 inch center to center dimension, which sets the drilling distance between holes and supports consistent layout across multiple cabinet fronts.
The pull measures 5-3/8 inch in total length, giving a grip that visually fits most standard cabinet doors and drawers without overwhelming narrower fronts.
The cabinet pull uses zinc die cast construction, providing a solid metal body that handles repeated opening and closing on active cabinet locations.
The pull has a smooth satin nickel finish, which delivers a soft metallic look that coordinates with many contemporary hinges, faucets, and appliances.
The pull projects 7/8 inch from the cabinet face, giving finger clearance while keeping the handle close enough to maintain a neat cabinet profile.
The pull has a 1/2 inch width across its front, creating a slim visual line on the cabinet while still offering enough surface area for a secure grip.
The Schaub and Company Italian Designs Series zinc die cast pulls in smooth satin nickel finish combine a 5-3/8 inch length, 5-1/16 inch center to center, 7/8 inch projection, and 1/2 inch width to support consistent cabinet layouts. For projects calling for Italian Design cabinet hardware with a satin nickel look, this pull offers fixed dimensions that align drilling, grip clearance, and visual balance across doors and drawers.