polished brass cup pull 3 inch cc describes a Schaub and Company cup/bin handle from the Traditional Series that uses a 3 inch center-to-center drilling, so it lines up with standard cabinet hole spacing on many traditional drawer fronts. The solid brass construction forms a rigid pull body, which supports repeated opening and closing on busy kitchen, bath, or shop cabinets. A polished brass finish creates a bright surface, which visually matches other polished brass decorative hardware in the same area. The handle length of 3-3/4 inches provides a wider gripping edge than the drilling dimension, which gives fingers more contact area during use. A projection of 1 inch spaces the hand slightly off the drawer face, which helps users grab the cup shape without rubbing knuckles against the front. The Schaub & Company brand and Classic/Traditional Series designation identify this pull as part of a coordinated decorative hardware family for consistent styling.
The center-to-center measurement of 3 inches defines the drilling pattern for this Schaub and Company cup/bin handle, so cabinet fronts using that spacing can accept the pull without changing hole locations. The 8-32 x 1 inch screw size specified for this model sets the threaded interface, which aligns with a common cabinet hardware standard and supports engagement through typical drawer front thicknesses. With a 1 inch projection, the pull extends slightly from the surface, which maintains enough depth for fingers to curl under the cup edge during operation. The 3-3/4 inch overall length positions the cup profile across more of the drawer width, which affects visual balance when the pull is centered on the face. The Traditional Series and Classic Series references identify the styling lane of this hardware, which matters when matching existing Schaub & Company decorative components in a room.
This Schaub cup/bin handle centers at 3 inches, which aligns with a widely used cabinet pull spacing for face-frame and frameless drawer fronts in many woodworking projects. The solid brass material defines this as a decorative metal pull, which suits kitchens, baths, built-ins, and shop cabinetry that call for a traditional brass look. With an overall length of 3-3/4 inches, the pull sits proportionally on medium-width drawers, which helps keep the hardware visually centered without overpowering smaller faces. The polished brass finish and Traditional Series label mark it as a classic styling choice, which supports use in restorations or new work that repeats established brass hardware themes. Because the projection is 1 inch, the handle stands off just enough from the surface, which keeps the pull compact while maintaining finger room behind the cup lip during daily operation.
The defined 3 inch center-to-center drilling on this Traditional Series pull sets a predictable layout, which simplifies marking, drilling, and repeating hole positions across multiple drawers in a run. The 8-32 x 1 inch screw size specification creates a known fastener interface, which helps installers select matching screws when working with varying drawer front thicknesses in the same project. Solid brass construction means the pull is formed from brass throughout, which provides a consistent base metal for any future finish coordination with other Schaub & Company pieces. The 1 inch projection stays constant from pull to pull, which maintains a uniform reveal and hand clearance line across a bank of drawers. The combination of 3-3/4 inch length and cup/bin profile defines the hand contact area, which helps installers position each pull at the same height for a consistent grab point. The polished brass finish specification keeps color and sheen uniform across multiples, which matters on longer cabinet runs where small finish differences can stand out.
This Schaub & Company cup/bin handle uses a 3 inch center to center drilling, which matches many standard cabinet layouts and guides where to place the two mounting holes on the drawer front.
The cup pull length is 3-3/4 inches with a 1 inch projection, which sets the visible width on the drawer and the stand-off distance that creates finger room behind the pull.
The Schaub 730-03 handle is made from solid brass, which gives the pull a metal construction suited to decorative cabinet hardware applications.
This Traditional Series cup pull has a polished brass finish, which provides a bright brass appearance that coordinates with other polished brass decorative items.
This Schaub & Company cup/bin handle lists an 8-32 x 1 inch screw size, which defines the thread and length pairing used to fasten the pull through standard cabinet fronts.
This pull carries the manufacturer part number 730-03 and is referenced as part of the Traditional Series and Classic Series of Schaub & Company solid brass pulls.
The Schaub and Company 730-03 polished brass cup/bin handle pairs a 3 inch center-to-center drilling with a 3-3/4 inch length, which supports straightforward alignment across cabinet drawers. Solid brass construction and a polished brass finish define the decorative profile, which works wherever Traditional Series styling is preferred. With a 1 inch projection and specified 8-32 x 1 inch screw interface, the pull offers consistent stand-off and fastening points from drawer to drawer. Select this Classic Series model when a 3 inch center-to-center polished brass cup pull is needed to coordinate with other Schaub & Company hardware.