polished brass cup pull 3 c c describes a cup or bin handle with a 3 inch center-to-center drill pattern, which positions the mounting holes for straightforward layout on cabinet fronts and drawer faces. The Schaub & Company 731-03 cup/bin handle uses this 3 inch center-to-center spacing, allowing consistent alignment across multiple doors and drawers in the same run. The handle is part of the Traditional Series, so its shaping and proportions support classic cabinet and furniture styles where a cup pull is preferred. The pull is made from solid brass, which provides a dense, weighty feel in the hand that suits higher-end cabinetry work. Its polished brass finish presents a bright, reflective surface that ties in with other polished brass decorative hardware in the same space, helping maintain a unified look on face frames and drawer banks.
The Schaub cup/bin handle with 3 inch center-to-center spacing anchors through the cabinet face, so the hole pattern directly follows the 3 inch dimension for an accurate fit. The specified projection of 1 inch defines how far the grip area sits off the surface, which affects how fingers reach under the lip of the cup during everyday use. The 4-5/8 inch overall length tells you how much horizontal space the pull occupies on the drawer or door front, guiding placement away from panel edges or neighboring hardware. The pull uses 8-32 x 1 inch screws, so the mounting interface follows a common cabinet thread standard for solid brass pulls. Together, these dimensions and screw details create a predictable installation pattern for repeat work on matching cabinets or furniture pieces.
The Schaub & Company 731-03 Traditional Series cup/bin handle is intended for use on cabinet doors and drawers where a cup pull style is desired. Its 3 inch center-to-center dimension matches a common drill pattern in cabinetry, which supports use on many new cabinet builds that are laid out for 3 inch pulls. The 4-5/8 inch overall length suits standard drawer widths, giving enough span for a hand grip without overwhelming smaller fronts. The polished brass finish works in projects that specify polished brass decorative hardware, creating continuity with hinges, knobs, and other pulls in the same finish family. Because the pull is solid brass, it aligns well with higher-grade millwork and casework where material quality is part of the specification and where a solid metal pull is preferred over lighter alternatives.
The pull's Traditional Series design offers a consistent profile, so using the same 731-03 part across a kitchen run or bank of built-ins keeps hole locations and visual lines repeating from cabinet to cabinet. The 3 inch center-to-center spacing simplifies jig setup, because a single drilling template can be used across all fronts that share this pull. Solid brass construction gives the handle a stable structure, which supports dependable seating against the cabinet surface when tightened with 8-32 x 1 inch screws. The 1 inch projection is defined, so clearances relative to neighboring doors, drawers, or trim can be planned in advance without guesswork during install. The polished brass finish is specified, allowing it to be matched with other polished brass pulls and knobs from the same Traditional Series in a hardware schedule, which streamlines selection when standardizing finish throughout a project.
The Schaub & Company 731-03 cup/bin handle has a 3 inch center-to-center dimension, which sets the spacing between mounting holes for drilling and layout on cabinet faces.
The cup pull has an overall length of 4-5/8 inches, which defines how much horizontal space it occupies on the drawer or door front during layout and installation.
The 731-03 cup/bin handle has a 1 inch projection, which determines how far it stands off the cabinet surface and how fingers access the pull.
The 731-03 Traditional Series cup pull is made from solid brass, giving it a substantial feel and aligning with cabinet projects that call for solid brass decorative hardware.
The Schaub & Company 731-03 pull uses 8-32 x 1 inch screws, which match a common cabinet hardware thread and length for fastening through typical door and drawer front thicknesses.
The 731-03 cup/bin handle has a polished brass finish, which provides a bright appearance that coordinates with other polished brass cabinet hardware.
The Schaub & Company 731-03 Traditional Series cup/bin handle combines a 3 inch center-to-center layout, solid brass construction, and a polished brass finish for coordinated cabinet work. Use its defined 4-5/8 inch length and 1 inch projection to plan consistent drilling, spacing, and visual alignment across your next cabinet or furniture project.