Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Polished nickel pull 4 C C describes a Schaub & Company Plain Handle designed with a 4 inch center to center hole spacing, which sets the mounting points so it lines up cleanly on standard cabinet door and drawer layouts. The polished nickel finish reflects light off the surface, giving a crisp, clean look that ties in well with other polished nickel decorative hardware in the same run of cabinetry. Construction from solid brass creates a dense, rigid handle body, so the pull feels substantial in use and holds its shape under repeated opening and closing over time. The Traditional Series design keeps the handle profile simple and plain, which suits classic cabinet styles where a straightforward pull is preferred. The 4-3/8 inch overall length leaves a small margin beyond the mounting holes, helping cover old marks when replacing an existing 4 inch pull.
The Schaub and Company 732-PN pull uses a 4 inch center to center measurement, so installers lay out or drill two mounting holes on that exact spacing for a proper fit. A 4-3/8 inch overall length means the ends reach slightly beyond the hole locations, which helps cover small chips at the bore edges or finish transitions from prior hardware. With a 1-1/8 inch projection, the pull stands off the cabinet surface enough for a solid grip without extending too far into walkways or tight clearances. The 8-32 x 1 inch screw size matches a standard cabinet hardware thread, so the handle is designed to seat against typical cabinet fronts drilled for that fastener length. Together, these dimensions guide on-center layout, drilling depth, and door or drawer clearance planning.
This Schaub Plain Handle centers 4 inch pull in polished nickel is part of the Traditional Series, so it is suited to classic cabinet layouts where uniform 4 inch boring is already in place. The 4-3/8 inch length helps when swapping older pulls on face frame or frameless cabinets because it spans slightly beyond the mounting holes, giving a bit of coverage over small wear marks. The 1-1/8 inch projection keeps the pull close enough to the cabinet face for narrow passage areas, while still giving room for fingers on drawers and doors of standard thickness. Its polished nickel finish lets it visually coordinate with matching polished nickel hinges or knobs used on the same installation line. The solid brass material supports use on frequently operated doors and drawers in kitchens, baths, or built-ins where a metal pull is preferred.
The defined 4 inch center to center dimension on the 732-PN pull supports repeatable drilling with cabinet hardware jigs set to that spacing, so multiple doors and drawers can be bored on the same setting. The 8-32 x 1 inch screw size corresponds to a common hardware fastener length, which aligns with standard cabinet front thickness where through-bored holes are used. A 1-1/8 inch projection provides a predictable standoff from the cabinet surface, helping maintain consistent finger clearance across a whole bank of doors. The polished nickel finish on solid brass offers a uniform surface that aligns with other Schaub Traditional Series pieces specified in the same job, which helps maintain visual continuity from one cabinet section to the next. The plain handle profile simplifies layout decisions because orientation and alignment are straightforward along horizontal or vertical runs.
The Schaub 732-PN pull has a 4 inch center to center spacing, a 4-3/8 inch overall length, and a 1-1/8 inch projection, which together define drilling layout, coverage, and finger clearance.
The 4 inch center to center spacing matches a common cabinet boring pattern, allowing installers to use standard jigs and replace existing 4 inch pulls without changing hole locations.
The solid brass construction provides a dense metal body for the pull, so it feels substantial in hand and resists flexing during frequent opening and closing of doors and drawers.
The 1-1-8 inch projection sets a consistent stand-off from the cabinet face, giving space for fingers while keeping the pull relatively close to the door or drawer front.
The polished nickel finish provides a bright, reflective surface that coordinates with other polished nickel decorative hardware for a unified look along a cabinet run.
This polished nickel cabinet handle is designed for 8-32 x 1 inch screws, aligning with standard cabinet hardware threading and typical door or drawer front thickness.
The Schaub & Company Plain Handle Centers 4 inch, Polished Nickel, 732-PN uses a solid brass body, polished nickel finish, 4 inch center to center spacing, and 1-1/8 inch projection to support consistent cabinet hardware layouts. When a Traditional Series plain handle profile is needed to match existing classic styling, these defined dimensions and finish details help align drilling, coverage, and visual coordination across the job. Select this polished nickel pull 4 C C when that specific size, finish, and straightforward Traditional Series design fit the cabinet run you are building or updating.