Empire Series, Zinc Die Cast Pulls 4" c/c, Antique Nickel Finish

Empire Series Zinc Die Cast Pull For Cabinets

Empire Series zinc die cast pull from Schaub and Company provides a 4 inch center to center grip, giving standard spacing that lines up with many cabinet drilling layouts and keeps handle placement consistent across doors and drawers. The antique nickel finish on this pull delivers a muted metallic look, which helps it blend with traditional and transitional cabinet styles where a softer metal tone is preferred. Its zinc die cast material creates a solid-feeling handle body, supporting everyday opening and closing loads on typical residential cabinetry. The pull measures 4-7/8 inches in overall length, spanning beyond the mounting holes to cover the hand area and visually scale to common drawer fronts. A projection of 1-1/4 inches stands the pull off the face of the cabinet, creating clearance for fingers while operating doors and drawers.

Empire Pull Details That Support Cabinet Work

• The 4 inch center to center dimension sets predictable mounting points, which simplifies layout when drilling or reusing existing holes on doors and drawers.
• The 4-7/8 inch overall length extends past the fastener points, giving a broader visual footprint that can better match wider drawer fronts or taller door rails.
• The 1-1/4 inch projection establishes a fixed standoff from the cabinet face, providing finger clearance for gripping without bringing the hand too far out from the door plane.
• The antique nickel finish defines the surface color and sheen, helping coordinate this pull with other antique nickel decorative hardware across the same installation.
• The zinc die cast material forms the pull body, creating a rigid component suited to the repeated hand force applied during normal opening and closing cycles.

Mounting Details For Empire Series Cabinet Pull

This Schaub and Company Empire Series pull uses a 4 inch center to center mounting layout, so the two fastener points are spaced to match that common handle pattern on many cabinet faces. The pull projects 1-1/4 inches from the surface, which sets the working clearance between the cabinet and the hand when gripping. Its 4-7/8 inch overall length defines the amount of handle visible across the front, affecting how it aligns with door stiles or drawer widths. The handle is made from zinc die cast material, so each mounting point secures a solid cast body to the cabinet front for everyday operation. The antique nickel finish covers all exposed surfaces, tying the installed pull into projects that use the same finish family on other decorative hardware.

Using The Antique Nickel Empire Pull In Projects

Where The 4 Inch Empire Pull Fits Best

The 4 inch center to center dimension on the Empire Series zinc die cast pull suits cabinet work that follows this standard drilling pattern on doors and drawers, allowing straightforward alignment with existing or planned hole layouts. At 4-7/8 inches long, the pull visually fits many kitchen and bath cabinet fronts, giving enough span to look proportional on common drawer widths and door rails. The 1-1/4 inch projection places the gripping surface off the cabinet face, creating a defined gap that supports typical finger access when opening base or wall cabinets. Its antique nickel finish matches projects that specify this finish across decorative hardware, helping maintain a consistent metal tone on pulls in the same room. The zinc die cast construction provides a cast-metal handle body for these cabinetry applications.

Details That Support Consistent Pull Installation

The Schaub and Company Empire Series pull with 4 inch center to center spacing allows installers to repeat the same drilling dimensions across multiple fronts, which supports uniform handle placement throughout a run of cabinets. Its 4-7/8 inch overall length aids visual alignment when setting pulls relative to door edges or drawer centers, since the full handle span can be centered or offset to a known distance. The 1-1/4 inch projection creates a consistent standoff, so all pulls along a cabinet line present the same hand clearance and profile from the face. The antique nickel finish unifies the appearance, so every installed pull presents the same color and surface look wherever it is used. Zinc die cast material keeps the handle body consistent from piece to piece across a project.

Common Questions About This Schaub Empire Pull

Selecting This Antique Nickel Pull For Your Job

The Empire Series zinc die cast pull in antique nickel from Schaub and Company combines a 4 inch center to center layout, 4-7/8 inch overall length, and 1-1/4 inch projection, giving defined mounting and hand-clearance characteristics for cabinet work. Its zinc die cast construction and antique nickel finish establish both the handle body and visual tone, supporting projects that call for this style and color of decorative hardware across doors and drawers. Using the part number 877-AN helps align multiple pulls to the same model when planning or executing a cabinet hardware installation.