Berenson Transitional Advantage Three Series 2-1/2" (64 mm) Center to Center Verona Bronze Cup Pull, - 9360-10VB-P

Berenson Transitional Advantage Three Cup Pull Use

Berenson Transitional Advantage Three cup pull is a zinc die cast cabinet handle in the Advantage Plus collection, so it serves as a decorative and functional pull for cabinet doors and drawers in the same design family. The Verona Bronze finish gives the pull a bronze-tone appearance, so it visually supports warm-toned cabinet finishes without drawing focus away from the door or drawer face. The 2-1/2 inch, or 64 mm, center to center drilling sets the mounting holes at a common size, so it works where that hole spread is already laid out on face frames or drawer fronts. The overall length of 3-3/16 inches gives you a hand grip that covers the drilling span cleanly, so the pull visually bridges the holes without excess overhang. The Transitional Advantage Three design language ties into the Berenson cabinet hardware range, so it helps create consistent styling across multiple cabinets in a room.

Key Dimensions And Material Details In Practice

• The zinc die cast material forms the body of the pull, so it offers a solid, uniform base that accepts the Verona Bronze finish cleanly and keeps the handle profile consistent across multiple pieces.
• The Verona Bronze finish is applied over the zinc die cast pull, so it delivers a bronze color tone that coordinates with similar decorative hardware and supports a unified look on banks of doors and drawers.
• The 2-1/2 inch, or 64 mm, center to center measurement defines the distance between mounting holes, so it aligns with cabinets drilled to that standard layout, simplifying layout when you repeat the same pull across a run.
• The 3-3/16 inch overall length spans beyond the mounting points, so the ends of the cup pull extend slightly past the screw holes, covering the drilled area and presenting a finished edge against the cabinet surface.
• The 1 inch projection measures how far the pull stands off the cabinet face, so it offers finger clearance between the cup and door or drawer front while keeping the handle profile tight to the surface line.
• The 1-1/16 inch width sets the vertical dimension of the pull, so it defines how much space the cup occupies on the face of the cabinet, helping you align it proportionally on narrow or wider fronts.

Installation Fit Based On Center To Center Size

The 2-1/2 inch, or 64 mm, center to center drilling dimension establishes the core installation pattern for this Berenson Transitional Advantage Three cup pull, so it slots directly into layouts using that hole spread on cabinet doors and drawers. The 8-32 screw size specified in the product data defines the thread engagement for the pull, so it pairs with standard cabinet mounting holes tapped or drilled for that machine screw diameter. The 1 inch projection works with this drilling layout by keeping the grip within easy reach, so fingers can wrap under the cup without contacting the door or drawer face. The 1-1/16 inch width complements the center to center spacing, so when the pull is aligned horizontally on a drawer front, the visible height of the cup pull remains balanced relative to the screw spacing and the drawer rail height.

Using This Verona Bronze Cup Pull On Projects

Where This 64mm Center Cup Pull Fits Best

The 64mm center to center measurement on this Berenson Transitional Advantage Three cup pull aligns with cabinets drilled for 2-1/2 inch pulls, so it suits replacement scenarios where existing holes already follow that standard. The Verona Bronze finish coordinates with cabinetry that uses bronze-tone decorative hardware, so it works on face frames and slab fronts designed with warmer stains or paint colors. The 3-3/16 inch length allows the pull to sit centered over the drilling on drawer faces, so the ends land close to the drilling points and visually frame the hardware against rails or stiles. The 1 inch projection keeps the pull close to the door or drawer front, so it maintains a low-profile hardware line on cabinets where minimal protrusion is preferred while still allowing a functional grip space within the cup.

Why These Dimensions Support Consistent Results

The defined 2-1/2 inch, or 64 mm, center to center dimension on this Advantage Plus collection pull lets installers repeat the same drilling pattern across multiple doors and drawers, so alignment stays consistent from cabinet to cabinet. The 1-1/16 inch width provides a predictable vertical footprint, so hardware lines stay even when the pull is referenced from the top edge or centerline of a drawer or door rail. The 3-3/16 inch length offers a fixed horizontal span from end to end, so when multiple pulls are installed on a wide bank, the visual spacing between pulls looks uniform. The combination of zinc die cast construction and Verona Bronze finish keeps the color and shape consistent across units, so long cabinet runs maintain the same profile and tone as hardware is repeated.

Common Questions About This Berenson Cup Pull

Selecting This Pull For Matching Cabinet Runs

The combination of 2-1/2 inch, or 64 mm, center to center drilling and 3-3/16 inch length makes this Berenson Transitional Advantage Three cup pull a practical choice where that mounting pattern is already planned or in place. The Verona Bronze finish and 1-1/16 inch width create a compact, bronze-tone profile that aligns with other Advantage Plus pieces on the same project. The zinc die cast construction and 1 inch projection tie form and function together, so the pull provides a usable grip while keeping the cabinet face visually clean. For cabinet runs using bronze-tone hardware at a 64 mm layout, this pull matches that specification and styling.