Kreg Tool unfinished pine pocket-hole plugs are solid-wood plugs designed to fill exposed pocket-holes when those holes will not be hidden on the backside of a project. The unfinished pine material accepts standard woodworking finishing steps so the filled hole can visually blend with pine components in the build. Each plug is cut as a high quality, trimmable piece, so the installer can flush-trim it after the glue sets and then sand it level to the surrounding surface. This set is configured for use with materials from 1/2 inch to 1-1/2 inch thick, matching common casework, face frames, and furniture parts. The plugs are part of a Kreg system that is offered in seven solid wood species and five plastic plug colors, so pine can be matched or contrasted alongside other Kreg plug options when planning visible joinery.
These Kreg Tool unfinished pine wood pocket-hole plugs are sized for pocket-holes drilled in materials from 1/2 inch to 1-1/2 inch thick, so the plug depth and taper are matched to the standard Kreg-style pocket profile. After the plug is glued into the pocket-hole, its trimmable solid-wood form lets the installer cut it flush with a saw or chisel, then sand it smooth with the panel surface. Because the pine stock is unfinished, it can be processed through the same sanding and finishing steps as the surrounding pine parts, which streamlines the workflow when closing pocket-holes across a run of cabinets or furniture components.
The Kreg Tool unfinished pine wood pocket-hole plug, P-PIN, is intended for situations where pocket-holes will not be hidden on the backside of a project, such as exposed cabinet ends, visible face frames, or furniture sides. In these locations, the solid-wood pine construction allows the filled pocket to resemble the surrounding pine instead of showing an open cavity. Because the plugs work with materials from 1/2 inch to 1-1/2 inch thick, they cover common panel and frame thicknesses in cabinetmaking and general woodworking. The fact that Kreg offers related plugs in seven solid wood species and five plastic plug colors also lets shops coordinate this pine version with other visible joints across mixed-material installations.
The high quality, trimmable, solid-wood construction directly supports repeatable results, because each plug can be shaved and sanded to the same flush level with the work surface. Using unfinished pine means the filled holes accept the same sanding grits and finishing schedule as the rest of the pine components, reducing variability across multiple cabinets or built-ins. The specified range for materials from 1/2 inch to 1-1/2 inch thick means the plugs are matched to the pocket depth typically produced by Kreg pocket-hole drilling in those thicknesses, which helps the plug seat properly without over-protruding or sitting too deep. As a result, installers can handle runs of pocket-hole filling with a consistent trim-and-finish routine using this P-PIN pine plug format.
The Kreg Tool P-PIN pocket-hole plugs are made from unfinished pine solid wood, which lets the filled holes take typical pine finishes for a more consistent appearance.
These Kreg Tool unfinished pine wood pocket-hole plugs are designed for use with materials from 1/2 inch to 1-1/2 inch thick, matching common cabinet and furniture stock sizes.
The Kreg Tool unfinished pine plugs are high quality, trimmable, solid-wood pieces, so after installation they can be cut flush and sanded for a smooth, finish-ready surface.
These Kreg Tool unfinished pine wood pocket-hole plugs are intended for use when pocket-holes will not be hidden on the backside of a project or when highlighting the holes decoratively.
The Kreg Tool P-PIN unfinished pine plugs are described for highlighting pocket-holes decoratively, so they can be used where a visible plugged detail is desired.
These unfinished pine plugs are part of a Kreg range offered in seven solid wood species and five plastic plug colors, so pine can be matched alongside other plug types.
The Kreg Tool unfinished pine wood pocket-hole plug, P-PIN, gives shops a pine-specific way to close pocket-holes in materials from 1/2 inch to 1-1/2 inch thick where those joints remain visible. The high quality, trimmable, solid-wood format supports a straightforward glue, trim, and sand workflow on exposed cabinet ends, face frames, or furniture parts. For projects built from pine stock that rely on pocket-hole construction, this plug style aligns the joint appearance with the surrounding wood, while fitting into the broader Kreg plug system for other species and colors across the shop.
Sold In: 1 Package