Pro Value Steel Series 3-3/4" (96 mm) Center to Center Satin Nickel Pull, - STBOW96-SN

Pro Value Series Steel Pull For Cabinets

Pro Value Series steel pull gives a straightforward bow-style handle that suits cabinet and furniture applications where a clean, modern line is preferred. The pull uses steel construction, which provides a solid feel in the hand during daily opening and closing of doors or drawers. A satin nickel finish on the steel pull softens reflections, helping the handle sit visually between stainless and chrome on installed casework. The 3-3/4 inch (96 mm) center to center drilling aligns with a common boring pattern, so the pull fits standard layouts on many new or existing fronts using that spread. Overall 4-9/16 inch length gives finger clearance beyond the mounting holes, helping users grab the handle without crowding knuckles against the face. A projected depth of 1-3/16 inch stands the grip far enough off the surface to grasp from above or below in typical cabinet runs.

Key Pull Details That Support Daily Use

• The pull is part of the Steel collection, tying it to a consistent material family for projects where matching the feel and construction of multiple handles across a space matters.
• Steel material provides a firm, non-flexing grip, which is useful on heavier cabinet or furniture fronts that are opened repeatedly throughout the day.
• Satin nickel finish delivers a muted metallic look, helping the pull coordinate with other satin nickel decorative hardware in the same room for a unified appearance.
• The 3-3/4 inch (96 mm) center to center dimension matches a widely used drilling size, assisting with straightforward alignment on standard cabinet door and drawer boring patterns.
• A projection of 1-3/16 inch sets the handle off the surface, creating hand clearance that can help users grasp the pull even when fronts are slightly proud of adjacent panels.
• The 3/8 inch width keeps the profile slim, which can be helpful where several pulls sit close together on narrow drawer fronts or tight modular layouts.

Mounting Details For 96 Mm Steel Pull

The 96 mm center to center measurement defines where to locate the two mounting holes, guiding drilling when the pull is installed on new cabinet or drawer fronts. The pull length of 4-9/16 inch means the handle extends slightly beyond the hole spacing at each end, which helps visually center the grip over the boring pattern. A projection of 1-3/16 inch determines how far the grip stands off the face, affecting how easily fingers slide behind the handle on thicker doors. The 3/8 inch width controls how much of the rail or drawer front the handle visually covers, which matters when lining up multiple pulls along a bank of fronts.

Using This Satin Nickel Pull In Real Projects

Where The Pro Value Series Steel Pull Fits

This Pro Value Series steel pull is categorized under decorative hardware and moldings, handles and pulls, placing it in the group typically used on cabinet doors, drawers, and furniture fronts. The satin nickel finish supports use in projects where other satin nickel components are specified, such as hinges or knobs from similar finish families. With a 3-3/4 inch (96 mm) center to center layout, the handle works on fronts that have been bored to that standard spacing, which is common across many kitchen, bath, and shop cabinets. The 4-9/16 inch overall length sits proportionally well on medium-width drawer faces or door rails that need a pull long enough to grasp without dominating the panel.

Details That Help Repeatable Hardware Results

The defined 96 mm center to center dimension lets installers or fabricators set up jigs or templates for repeat drilling across multiple fronts, reducing layout variation from cabinet to cabinet. Length at 4-9/16 inch and projection at 1-3/16 inch give consistent physical reference points, so each pull sits at the same stand-off and overhang, supporting a uniform appearance along a run of doors and drawers. The 3/8 inch width keeps the contact area narrow, which is useful when aligning several pulls on narrow stiles without overlapping edges or decorative profiles. The manufacturer part number STBOW96-SN identifies this exact bow pull configuration in the Steel collection, helping buyers match previous installs or specify the same model for additional casework runs where continuity of hardware is important.

Common Questions About The STBOW96-SN Pull

Selecting This Satin Nickel Pull For Your Project

The Pro Value Series steel pull with 3-3/4 inch (96 mm) center to center spacing, 4-9/16 inch length, and 1-3/16 inch projection offers a defined set of dimensions for cabinet or furniture fronts. Steel construction and a satin nickel finish tie the handle to the Steel collection, supporting projects that call for a consistent metal look and feel across multiple pieces. Using the STBOW96-SN part number lets buyers specify this exact bow pull when planning new work or extending existing runs of satin nickel decorative hardware.