Table Bases Decorative 3 Leg Table Base - 26"W x 28"H

Decorative 3 Leg Table Base For Stable Work Surfaces

Decorative 3 leg table base defines this Peter Meier, Inc. support for work surfaces and tables, giving installers a specific, repeatable solution when a centered base is preferred over individual legs. The 26 inch width and 28 inch height identify it as a base suited to standard table and work surface layouts where a consistent working height is important for planning surrounding cabinetry or seating. The design uses a 3 inch steel column, which provides a solid central spine for the three legs, so load is carried into one compact footprint instead of spread across multiple corner legs. The black matte finish establishes a low-glare, contemporary look that visually recedes under tops, which matters on open designs where under-table structure is exposed. As a table base within the Work Surface & Tables category, it fits naturally into new installations or upgrades that need clear leg room and a defined support point.

Key Table Base Details For Real-World Projects

• The 26 inch width specifies the spread of the decorative 3 leg table base, guiding layout when positioning the base under rectangular or small round tops so edge overhang and seating clearances can be planned predictably.
• The 28 inch height aligns this table base with common table and work surface heights, allowing fabricators to design tops and adjacent cabinetry around a known finished height target for consistent ergonomics across a room.
• The 3 inch steel column creates a compact central support zone, concentrating strength in a single vertical member so installers can route foot traffic and chair placement around one core rather than four separate corner legs.
• The black matte description signals a subdued, non-reflective surface, which helps this table base visually blend with darker interiors and keeps the focus on the work surface or tabletop rather than the supporting structure.
• The Peter Meier, Inc. branding identifies a dedicated table base manufacturer, giving shops a defined part family when they want to repeat the same base across multiple tables for a coordinated project.

Installation Height And Footprint Planning Details

The 26 inch width of this decorative 3 leg table base sets the working footprint, which helps installers position the base to balance the tabletop without pushing legs into knee space or walkway paths. With the height specified at 28 inches, the base supports standard table layouts where a consistent sit-down height is needed across multiple pieces in the same area. The 3 inch steel column concentrates vertical support, which influences how fasteners and mounting patterns can be arranged on the underside of the work surface. As a table base within the Work Surface & Tables family, it integrates cleanly into shop drawings where one central support is favored over perimeter legs.

Using This Peter Meier Table Base On Projects

Where This 3 Leg Steel Table Base Fits

This decorative 3 leg table base is part of the Table Bases product class, positioning it for use under work surfaces and tables where a central support is required instead of four separate legs. The 26 inch width places the three legs within a defined zone, which works well below compact rectangular or round tops used in work areas, small meeting tables, or shop surfaces. At 28 inches high, the base supports table heights aligned with typical seating, allowing designers to coordinate chair selection and adjacent casework around a consistent finished height. The black matte appearance suits applications where the base should visually recede under the top, such as open-frame designs where the underside remains visible from multiple directions.

Details That Support Consistent Results And Layout

The 3 inch steel column at the center of this Peter Meier table base provides a measurable, rigid core that simplifies layout when marking mounting locations under a work surface. Because the base is defined as decorative and 3 legged, it offers a balanced stance around that column, which helps distribute load without relying on wide corner spacing. The 26 inch width dimension lets fabricators calculate overhangs and clearances in advance, so repeated tables can share identical geometry across a project. The 28 inch height ties directly to how installers plan transitions between this table and nearby counters or built-ins, supporting straight sightlines and comfortable reach between surfaces. The 1026-29-MT part number gives shops a precise reference when reordering the same base for additional stations or matching replacements later.

Common Questions About This Decorative 3 Leg Base

Selecting This Base For Work Surfaces And Tables

This Peter Meier, Inc. decorative 3 leg table base combines a 26 inch width, 28 inch height, and 3 inch steel column to support work surfaces and tables with a compact, central footprint. The black matte finish keeps the base visually restrained, which suits installations where under-table structure remains visible. For projects that call for a defined table height and an unobtrusive support under the top, this 1026-29-MT table base offers a repeatable part number that aligns with the Work Surface & Tables category.