Berenson Harmony Series 3" (76 mm) Center to Center Verona Bronze Pull, - 9437-10VB-P

Berenson Harmony 3 Inch Pull For Cabinet Projects

Berenson Harmony 3 inch pull gives you a defined gripping point for doors and drawers because it has a 3 inch center to center mounting dimension. The pull is part of the Harmony Collection, so it maintains a consistent design language when multiple pieces from the collection are used on the same job. The material is zinc die cast, which provides a solid metal pull body that supports everyday opening and closing of cabinets. The finish is Verona Bronze, so the pull presents a bronze tone that supports warm color cabinet schemes. Overall length is 3-11/16 inches, giving extra handle length beyond the mounting holes for finger clearance. Projection is 1-1/8 inches, so the pull stands off the cabinet face enough for fingers to wrap around. Width is 11/16 inch, creating a defined front surface to grasp. Base dimensions are 9/16 inch, so each foot has a compact footprint on the cabinet face.

Key Harmony Pull Details For Cabinet Work

• The 3 inch center to center sizing sets the mounting hole spacing, which supports consistent drilling layouts across multiple fronts.
• The 3-11/16 inch overall length provides additional handle beyond the screw centers, giving more edge to grab when operating heavier drawers.
• The 1-1/8 inch projection sets the stand-off from the cabinet, helping fingers clear the door surface for a more positive pull action.
• The 11/16 inch width gives the front of the pull a defined gripping band, which can feel more secure under hand during repeated use.
• The Verona Bronze finish establishes a bronze visual tone, so the pull can coordinate with other bronze-finished decorative hardware on the project.
• The 9/16 inch base dimensions keep each mounting foot compact, helping the pull sit cleanly on narrower rail or stile widths.

Cabinet Pull Mounting Dimensions And Fit Use

The 3 inch center to center measurement defines the drill pattern, so jigs or templates set for 3 inch pulls can be used on this part. With a 3-11/16 inch overall length, the pull spans slightly beyond the mounting points, which can help balance the look on doors and drawers that are not very wide. The 1-1/8 inch projection determines how far the pull stands away from the cabinet face, so it creates room for fingers between the pull and the door or drawer front. A width of 11/16 inch shapes the gripping surface, which can influence how the pull feels when opening stacked drawers. Base dimensions of 9/16 inch at each end define the contact area on the cabinet, which matters when lining the pull up with narrow rails. Screw size is 8-32 x 1 inch, so the pull is threaded for that machine screw size during installation.

Using This Verona Bronze Harmony Pull In Workflows

Where This 3 Inch Center Pull Is Applied

This Harmony Series 3 inch center to center pull is suited to cabinet and drawer fronts that are drilled on a 3 inch pattern, because the mounting holes are spaced at that distance. The zinc die cast construction makes the pull a metal component in the decorative hardware and moldings category, which aligns with use on kitchen, bath, or built-in cabinetry where metal pulls are specified. The Verona Bronze finish lets this pull act as a bronze-tone option within Berenson decorative hardware, aligning with projects that call for bronze-colored handles and pulls. With a length of 3-11/16 inches, the pull works on small to medium fronts where a compact handle is desired rather than a long bar. The 9/16 inch base dimensions keep the mounting footprint relatively small, which supports placement on face frames with limited rail height.

Why Dimensions And Material Support Repeatable Results

The defined 3 inch center to center spacing allows installers to use existing 3 inch drilling templates, which can speed layout when multiple Harmony pulls are fitted on a job. The 1-1/8 inch projection sets a repeatable stand-off distance from the cabinet face, so door and drawer lines maintain a consistent pull clearance across a run. The 11/16 inch width controls how much of the hand rests on the pull, influencing the feel when repeatedly operating drawers that see frequent use. The zinc die cast material provides a uniform cast metal structure, which helps the pull feel consistent across all units specified under manufacturer part number 9437-10VB-P. The Verona Bronze finish creates a defined color tone, allowing designers or builders to carry the same bronze appearance from one cabinet bank to another. The specified 8-32 x 1 inch screw compatibility means the pull is threaded for that common cabinet screw, which aligns with standard installation methods in decorative hardware work.

Common Questions About The Harmony 3 Inch Pull

Select This Harmony Pull For 3 Inch Layouts

This Berenson Harmony Series 3 inch center to center Verona Bronze pull combines a 3-11/16 inch overall length, 1-1/8 inch projection, and 11/16 inch width to set a consistent hand feel on cabinet fronts. The zinc die cast construction and Verona Bronze finish define both material and appearance for decorative hardware projects. With base dimensions of 9/16 inch and compatibility with 8-32 x 1 inch screws, the pull aligns with standard cabinet drilling and fastening practices. For cabinet runs laid out on a 3 inch center pattern where a bronze-tone metal handle is specified, this Harmony pull matches those dimensional and finish requirements.