Berenson Harmony Series 5-1/16" (128 mm) Center to Center Verona Bronze Pull, - 9449-10VB-P

Berenson Harmony Verona Bronze Pull For Cabinets

Berenson Harmony Verona Bronze pull gives cabinets a defined 5-1/16 inch center to center grip point that sets consistent spacing between fasteners, so layouts stay uniform across doors and drawers on a run of cabinets. The zinc die cast construction forms a solid handle body, giving a firm feel when opening heavier cabinet fronts or pantry doors. A Verona Bronze finish provides a specific bronze tone along the full 5-11/16 inch length, supporting visual alignment when matching other Verona Bronze decorative hardware in the same space. The 1-1/8 inch projection sets the working stand-off from the cabinet face, leaving hand clearance while keeping the handle close enough to fronts for a compact profile. With a width of 11/16 inch, the pull presents a defined gripping surface without crowding narrow rail sections on cabinet doors.

Key Harmony Series Pull Details For Projects

• The 5-1/16 inch center to center measurement establishes a precise drilling pattern, which helps installers repeat hole locations accurately across multiple cabinet fronts in the Harmony Series layout.
• The overall 5-11/16 inch length extends slightly past the fastener points, giving visible handle ends that make alignment to cabinet edges easier during layout and installation work.
• The 1-1/8 inch projection holds the grip away from the surface, improving finger clearance while keeping the handle projection controlled for tight kitchen or bath installations.
• The 11/16 inch width defines the pull footprint on the door or drawer face, which helps plan rail sizing and visual balance on narrower cabinet members.
• The 9/16 inch base dimensions concentrate the contact area at each mounting point, which supports stable seating of the pull against the cabinet surface when tightening mounting screws.

Mounting Dimensions And Fit For This Pull

The 5-1/16 inch center to center dimension on this Berenson Harmony pull sets the distance between mounting points, guiding drill locations when fitting the handle to cabinet doors and drawers. An overall 5-11/16 inch length provides slight overhang beyond the mounting holes, which helps with visual centering on wider rails or drawer fronts. The 1-1/8 inch projection determines how far the pull stands off the cabinet face, allowing planning for hand clearance where doors open near walls or adjacent cabinets. With a width of 11/16 inch and base dimensions of 9/16 inch, the pull seats with a controlled footprint, helping the handle sit flat on the surface and align squarely to cabinet edges during installation.

Using The Harmony Series Pull In Cabinet Work

Where This Verona Bronze Pull Works Best

This Harmony Series cabinet pull with a 5-1/16 inch center to center span is suited to doors and drawers that have been drilled or laid out for that specific hole spacing, so the handle aligns directly over existing bores. The Verona Bronze finish matches projects that already specify Verona Bronze decorative hardware, allowing installers to keep a consistent finish across multiple cabinet runs in kitchens, baths, or built-ins. With a 5-11/16 inch overall length, the pull presents a visible bar on medium-width drawers and stiles, helping users locate the grip quickly during everyday use. The 1-1/8 inch projection gives space for fingers behind the pull, which helps on deeper cabinet fronts where a flush grip would be harder to grasp. A width of 11/16 inch means the pull sits comfortably on standard cabinet rails without overpowering narrow faces, while still giving enough surface for a confident handhold for frequent operation.

Details That Support Consistent Installation Results

The defined 5-1/16 inch center to center drilling dimension lets installers rely on templates or jigs set to that spacing, supporting fast and repeatable hole placement across a full job. The 5-11/16 inch total length offers a fixed reference for aligning the pull relative to drawer edges or door stile lines, which helps maintain straight visual lines when multiple Harmony pulls are mounted side by side. With a 1-1/8 inch projection, the handle sits at a consistent stand-off from the cabinet face, keeping the feel of every door and drawer pull similar across the project. The 11/16 inch width and 9/16 inch base dimensions define how the pull contacts the surface, helping the installer seat each base evenly so the handle does not rock when the mounting screws are tightened to typical cabinet substrates. The zinc die cast material creates a solid body for the pull, providing a stable feel under hand when users open and close doors and drawers throughout daily use.

Buyer Questions About This Harmony Cabinet Pull

Selecting This Harmony Pull For Your Next Job

The Berenson Harmony Verona Bronze pull with 5-1/16 inch center to center spacing combines a defined drilling layout with a 5-11/16 inch length suited to many cabinet doors and drawers. Its Verona Bronze finish matches projects specifying that exact finish, and the zinc die cast construction provides a solid handle body for regular cabinet use. When a job calls for this 128 mm center to center dimension in Verona Bronze, this Harmony Series pull provides the measurements needed for consistent cabinet hardware installation.