Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Berenson Puritan Series 3 inch pull is a zinc die cast cabinet handle in a brushed nickel finish, so it provides a defined grip point with a neutral metallic look for cabinets or furniture needing a 3 inch center to center pull. The pull has a 3 inch center to center drilling, so it aligns with standard 3 inch hole spacing on many cabinet doors and drawers to support straightforward replacements or new layouts built around that spacing. Overall length is 3-11/16 inches, so the pull extends beyond the mounting holes to give a full hand contact area for opening or closing fronts without crowding the mounting points. A projection of 1-1/8 inches places the handle away from the surface, giving fingers space behind the pull when operating doors or drawers. The 15/16 inch width presents a flat contact surface, helping fingers land consistently across the pull when it is used repeatedly.
The 3 inch center to center dimension on this Berenson Puritan pull sets the drilling distance for installation, so jigs or templates can be dialed to exactly 3 inches when preparing cabinet doors or drawers. The 3-11/16 inch overall length then frames how close the handle edges sit to panel edges, helping installers decide vertical and horizontal positioning on rails, stiles, or drawer fronts during layout. A projection of 1-1/8 inches fixes how far the pull stands off the surface, which guides placement when working near adjacent cabinets or walls, because it defines how much the handle extends into walk paths. The 3/8 inch base dimensions at each end determine the contact patch against the front, aiding in marking and verifying that both bases sit fully on flat areas of the cabinet face.
This Berenson Puritan Series 3 inch center to center pull fits cabinet or furniture fronts drilled on a 3 inch pattern, because the mounting holes on the pull are spaced to that distance. The 3-11/16 inch overall length works on many drawer and door widths by leaving some material visible at each side of the handle, which supports balanced looks on common residential cabinet layouts. With a 1-1/8 inch projection, the handle stands off enough from the face for gripping without placing the pull excessively far into the room, which helps when many doors or drawers in a bank open past each other. The 15/16 inch width offers a grasping surface that suits repeated use in busy spaces, giving stable finger placement on kitchen or shop cabinet fronts.
The 3 inch center to center measurement on this pull supports repeatable drilling patterns, because installers can reuse the same 3 inch setup across an entire project for both replacements and new cabinet runs. The 3-11/16 inch overall length creates a predictable envelope when laying out multiple pulls on doors or drawers, which simplifies alignment from cabinet to cabinet and reduces layout time. A 1-1/8 inch projection defines consistent hand clearance behind the pull, so users feel similar grip depth across different cabinets, supporting comfortable operation during daily use. The 15/16 inch width and 3/8 inch base dimensions together outline how the pull seats on the surface, which helps installers align the hardware square to edges and maintain even reveals from one front to the next.
This Berenson Puritan pull has a 3 inch center to center measurement, so hole spacing on cabinets or drawers must be set to 3 inches for the handle to mount properly.
The Berenson 9487-1BPN-P pull is 3-11/16 inches in overall length, so it provides grip area beyond the mounting holes on typical cabinet door and drawer widths.
This brushed nickel pull has a 1-1/8 inch projection, so the handle stands off the cabinet surface enough to give fingers clearance behind the pull when opening fronts.
The Puritan Series pull is made from zinc die cast material, so the handle body is formed in a precise mold to maintain consistent shape across multiple pieces.
This Berenson cabinet pull has a brushed nickel finish, so its visible surface presents a soft metallic look that coordinates with many brushed nickel fixtures.
The pull is 15/16 inch wide, so the front face offers a relatively broad surface for fingers to contact during repeated door or drawer operation.
This Berenson Puritan Series 3 inch center to center brushed nickel pull from Wurth Baer Supply pairs a zinc die cast construction with defined dimensions, giving installers clear drilling and layout targets on cabinet doors or drawers. The 3 inch center to center spacing, 3-11/16 inch overall length, 1-1/8 inch projection, 15/16 inch width, and 3/8 inch base dimensions together outline how the pull will sit and operate on the front, supporting consistent looks and predictable hand clearance. Use these measurements and the brushed nickel finish description to align this pull with the visual style and drilling pattern planned for your next cabinet or furniture installation.
Sold In: 1 Each
