Harmony Pull 96mm Center To Center Use

Harmony pull 96mm center to center describes a Berenson Harmony Series cabinet pull designed with a 3-3/4 inch center to center screw spacing, so it aligns with standard hole boring on many cabinet doors and drawers for straightforward layout and drilling on new work. The zinc die cast material gives the pull a solid metal construction, which supports everyday grabbing and pulling on frequently used fronts in a kitchen or shop. Its vintage nickel finish provides a toned metallic look that suits traditional and transitional projects where a muted metal color is preferred over bright chrome. The overall 4-7/16 inch length provides a comfortable gripping span along the face of the cabinet, helping hands land naturally without crowding the mounting points. A projection of 1-1/8 inch spaces the handle away from the door or drawer face, giving fingers clearance when gripping from above or below. The 11/16 inch width offers a balanced face profile, so the pull reads as substantial without overpowering narrow drawer fronts.

Key Harmony Pull Details For Cabinet Projects

• The 3-3/4 inch (96 mm) center to center dimension sets consistent hole spacing, which simplifies drilling jigs and speeds repeatable installation across multiple fronts.
• The 4-7/16 inch overall length creates a defined handhold, which helps users comfortably grip the pull in daily use on either doors or drawers.
• The 1-1/8 inch projection positions the pull off the surface, giving practical finger room that reduces knuckle contact against the cabinet face when opening.
• The 11/16 inch width keeps the pull visually proportioned, helping it sit well on both narrow and wider rails without looking oversized or undersized.
• The zinc die cast material provides a metal body, which supports a sturdy feel when fastening the pull to cabinet fronts with standard machine threads.
• The vintage nickel finish supplies a softer metallic tone, which works well where a project calls for a classic look rather than a bright, highly reflective surface.

Mounting And Fit Details For Harmony Pull 96mm

The Harmony pull 96mm center to center dimension means mounting holes are set 3-3/4 inches apart, so installers can use existing boring patterns that match this spacing on cabinet doors and drawers. The base dimensions of 9/16 inch at each end define the footprint against the cabinet surface, which helps in laying out clearances near edge profiles, neighboring pulls, or decorative trim. With an overall length of 4-7/16 inch, the pull provides coverage that can visually bridge older hole marks when replacing hardware using the same center spacing. The zinc die cast construction accepts 8-32 machine threads, aligning with the specified 8-32 x 1 inch screw size so the fastener engages reliably through common cabinet door and drawer front thicknesses.

Where This Berenson Harmony Pull Works Best

Using The Vintage Nickel Pull On Cabinets

The Berenson Harmony Series pull in vintage nickel is designed as decorative hardware for cabinet doors and drawers, so it suits applications in kitchens, baths, built-ins, and shop cabinetry where a unified look is desired. Its 3-3/4 inch (96 mm) center to center spacing corresponds to a widely used drilling standard, which supports using the pull in runs of base and wall cabinets without constantly changing jigs. The 4-7/16 inch overall length gives enough bar surface that users can grab the pull from different angles, which is helpful on taller pantry doors or wider drawers. With an 11/16 inch width, the pull sits comfortably on face frames and full-overlay fronts, offering visible hardware detail without covering too much of narrow rails or stiles. The 1-1/8 inch projection provides clearance for fingers even when the pull is mounted near adjacent doors, allowing doors and drawers to operate freely in tighter cabinet layouts.

Details That Support Consistent Installation Results

The specified 3-3/4 inch center to center measurement allows installers to rely on a single boring pattern, which shortens layout time and helps keep hardware perfectly aligned across long cabinet runs. Base dimensions of 9/16 inch at each mounting point define the contact area on the cabinet face, so the pull seats firmly against flat surfaces and covers the immediate area around the screw holes. The zinc die cast material pairs with the 8-32 x 1 inch screw size, giving a consistent machine-thread connection that resists loosening when properly tightened through standard door and drawer front thicknesses. The 1-1/8 inch projection and 11/16 inch width work together to present a grip that feels accessible from the top, bottom, or side, which is useful when positioning pulls at different heights for various cabinet zones. The vintage nickel finish maintains a classic metal appearance that coordinates well when repeating this same pull style across an entire room for visual continuity.

Common Questions About Harmony Zinc Die Cast Pull

Selecting This Harmony Pull For Your Cabinets

The Berenson Harmony Series 3-3/4 inch (96 mm) center to center vintage nickel pull offers a zinc die cast construction, a 4-7/16 inch overall length, and a 1-1/8 inch projection, so it fits common cabinet boring patterns while providing practical grip clearance and a classic metallic finish.