Pro Value Steel Pull 17-5/8" (448 mm) Center to Center, Stainless Steel, STBAR448-SS

Pro Value Steel Series Bar Pull For Cabinets

Pro Value Steel Series bar pull gives cabinets and furniture a straight steel handle with a stainless steel finish, so projects get a clean, modern line that matches other stainless details on the job. The pull uses a 17-5/8 inch center to center drilling, which sets hole spacing for larger cabinet doors or wide drawers and keeps layout consistent across runs. Its overall length of 20-13/16 inches extends past the mounting holes, so installers get comfortable hand clearance across wide fronts. The pull is made of steel, providing a solid feel when opening heavier doors in kitchens, baths, or built-ins. A stainless steel finish on the steel body delivers the stainless look that designers expect while aligning with other stainless hardware in the same space. The handle belongs to the Steel collection within the Pro Value Series, so it fits into projects already using that series.

Steel Pull Details That Support Cabinet Work

• The 448 mm center to center drilling matches the 17-5/8 inch spacing, which simplifies metric or imperial layout when boring rows on cabinet doors or long drawers in residential or commercial work.
• The 1-5/16 inch projection stands the pull off the front, giving fingers space behind the bar and reducing knuckle contact with the door or drawer face during frequent use in busy areas.
• The 1/2 inch width keeps the bar slim, which helps it sit neatly on narrow stile widths while still providing enough grip area for users to grab and pull heavy fronts comfortably.
• The stainless steel finish on the steel material supports a unified stainless look along appliance lines or metal fixtures, which helps designers keep finishes aligned across kitchens, baths, and casework.
• The Pro Value Series branding identifies this handle as part of a larger decorative hardware line, helping shops and installers keep projects visually consistent when mixing different sizes from the same family.

Bar Pull Mounting Dimensions And Layout Use

The 17-5/8 inch center to center dimension defines the drilling layout for this bar pull, so once that spacing is set in jigs or boring equipment, installers can repeat the pattern across multiple doors without re-measuring. The 448 mm metric center to center value mirrors the same spacing, helping shops that work from metric plans line up holes correctly. With an overall length of 20-13/16 inches, the bar extends beyond the screw locations, so there is a clear visual reference when aligning the pull parallel to the door edge. The 1-5/16 inch projection and 1/2 inch width together define how far the handle stands off and how much bar surface is available to grip during operation.

How This STBAR448-SS Pull Fits Real Projects

Using The 17-5/8 Inch Pull On Cabinets

This STBAR448-SS stainless steel pull is sized for doors or drawers that benefit from a long handle, so a single pull can serve wide cabinet faces where shorter pulls might look undersized. The 17-5/8 inch center to center spacing works well on tall pantry doors or wide drawer banks, because the longer spread helps distribute hand force when opening and closing. Its overall length of 20-13/16 inches creates a strong horizontal or vertical line, depending on orientation, which can tie together multiple cabinets in a run. The 1-5/16 inch projection gives room for users to wrap fingers behind the bar even when fronts sit tight to adjacent doors or walls. With a 1/2 inch width, the pull stays visually light on narrow rails yet still offers enough thickness for a steady grip in everyday kitchen or bath use.

Details That Support Repeatable Cabinet Installations

The matched 448 mm and 17-5/8 inch center to center measurements allow installers working from either metric or imperial drawings to use the same pull without conversion errors, which supports accurate jig setup and repeat drilling. Using the 20-13/16 inch overall length as a reference point, it becomes easier to center the bar on a panel or align multiple pulls across a bank of doors. The 1-5/16 inch projection sets a predictable stand-off from the face, which helps when planning clearances behind doors in tight corridors or near adjacent cabinetry. A consistent 1/2 inch width means routing or edge detailing around the pull area can be designed once and reused. Knowing this pull is part of the Pro Value Series Steel collection helps designers and shops specify matching pieces across an entire job with a single series reference. The manufacturer part number STBAR448-SS gives shops and installers a precise identifier to tie purchase orders, job drawings, and replacement needs back to the exact bar pull.

Common Questions About This Stainless Bar Pull

Selecting This Pull For Cabinet Projects

The Pro Value Steel Series bar pull with 17-5/8 inch (448 mm) center to center drilling, 20-13/16 inch overall length, 1-5/16 inch projection, and 1/2 inch width gives a defined layout for cabinets using a stainless steel finish. Its steel construction and place in the Pro Value Series Steel collection align with projects built around matching stainless-look decorative hardware. Using the STBAR448-SS part number from Wurth Baer Supply connects purchasing, design, and installation to the same long bar pull across current work and future repeat jobs.