Euro door stop bumper with screw white is a Fastcap door and drawer bumper that cushions cabinet doors using a soft rubber body, which helps reduce impact on the door and frame during everyday use. The bumper diameter of 9/16 inch creates a broad contact point, spreading door forces over a wider area so cabinet surfaces experience less concentrated wear at the stop location. The 5/16 inch height sets a consistent stand-off between the door and the cabinet, which helps maintain a repeatable gap where the door rests when closed. The off center screw hole in the bumper allows rotation to varied distances from the door, giving installers a built-in way to fine-tune how far the door sits off the face when at rest. This Euro-style layout supports clean, predictable stopping on inset or frameless cabinet projects where controlled clearances matter.
This Fastcap Euro door stop bumper uses a screw-mounted design with an off center screw hole, so the bumper fastens mechanically while still allowing rotational adjustment for final positioning. The 9/16 inch diameter and 5/16 inch height work together to define the final resting gap, so once the mounting point is chosen, the installer can rotate the bumper around the off center screw to move the effective stop point slightly closer to or farther from the door edge. Because the bumper is constructed of soft rubber, it compresses slightly under load, which helps absorb closing energy while still holding the door at the intended stand-off distance set by the 5/16 inch profile. This combination of screw mounting, rotational adjustability, and compressible rubber gives a controlled, repeatable stop that can be fine-tuned during cabinet fitting.
The Euro door stop bumper with screw white is identified in the product data as a Door and Drawer Bumpers class item, so it is suited to installations where a cabinet door or similar panel needs a defined resting point. Its 9/16 inch diameter makes it well sized for typical cabinet door edges, so the contact lands on a predictable strip of material instead of a very small corner. The 5/16 inch height helps establish a modest but functional gap, which works well in Euro-style and inset cabinet layouts where doors should sit close while avoiding direct wood-to-wood contact. Because the bumper is constructed of soft rubber and specified in white, it aligns with projects using light-toned casework where a softer stop and a discrete appearance at the contact point are both important results.
The off center screw hole is a central feature for this Euro door stop bumper, because it allows the installed bumper to be rotated to varied distances from the door, directly affecting the resting position. By selecting the screw location and then rotating the bumper, an installer can subtly shift how far the 5/16 inch tall profile meets the door edge, which helps dial in exact reveals on individual doors without relocating the fastener point. The soft rubber body responds to these adjustments by compressing slightly, so minor rotation changes translate into smooth, progressive contact rather than abrupt stops. The 9/16 inch diameter keeps that adjusted contact area broad and stable, which supports consistent alignment over time as the same edge engages the bumper on each close. Together, these verified details give practical control over door stop depth while still relying on a simple screw-mounted part.
The Euro door stop bumper with screw white is constructed of soft rubber, which cushions door contact and helps reduce impact on cabinet surfaces during closing.
The 9/16 inch diameter spreads contact over a wider area, while the 5/16 inch height sets the stand-off gap, together defining how the door rests against the cabinet.
The off center screw hole allows the bumper to be rotated to varied distances from the door, providing simple adjustment of the final stop position after mounting.
The soft rubber construction cushions impact as doors close against the bumper, which helps limit noise and reduces concentrated stress at the stop point.
The product class Door and Drawer Bumpers identifies this part as a stop element for doors or drawers, guiding its use wherever controlled resting points are needed.
The white color, as stated in the description, helps the bumper visually blend with light cabinet interiors or painted components while it performs its stopping function.
The Fastcap Euro door stop bumper with screw white combines soft rubber construction, a 9/16 inch diameter, and 5/16 inch height to control how doors meet the cabinet. The off center screw hole adds rotational adjustability, so stop depth can be tuned around the fixed mounting point. With its Door and Drawer Bumpers classification and white finish, this part fits cabinet jobs that need a defined, cushioned stop with a discreet look at the contact point.
Sold In: 1 Package
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 1 Package |  FAEURODOORSTOP-B Mfr# EURO DOOR 10 BROWN | FastCap inset euro doorstop, 10 pk,brwn | ||||
Sold in: 1 Package | FAEURODOORSTOP-BWS Mfr# EURO DOOR 10 SCR BRW | Euro Door Stop Bumper with Screw, Brown | ||||
Sold in: 1 Package | FAEURODOORSTOP-W Mfr# EURO DOOR 10 WHITE | FastCap inset euro doorstop, 10 pk,wht |