Hickory Hardware Sunnyside 3" (76 mm) Center to Center Polished Chrome Pull, P115-26

Hickory Hardware Sunnyside Pull For Cabinets

Hickory Hardware Sunnyside pull is a zinc die cast handle in the Sunnyside Series designed for cabinet and drawer applications where a 3 inch center to center layout is already in place. The pull has an overall length of 4 inches, so it spans beyond the mounting holes to give a comfortable gripping area on doors or drawers. Its 3/4 inch projection sets the hand away from the surface enough for easy grasping while opening or closing. A width of 1/2 inch keeps the pull visually light while still giving a defined edge to pull against. The polished chrome finish gives a bright, reflective look that coordinates with other chrome cabinet hardware. The product is identified as Belwith Keeler Manufacturer Part P115-26, which ties it directly to the Sunnyside Series design for consistent use across a project.

Key Sunnyside Pull Details For Daily Use

• The zinc die cast material provides a solid metal construction, which supports regular cabinet and drawer operation in kitchen, bath, or shop environments where pulls are used repeatedly.
• The 3 inch center to center mounting dimension matches common pre-drilled cabinet boring patterns, which simplifies layout when matching existing holes on replacement or new fronts.
• The 4 inch overall length extends slightly past the mounting points, which offers more finger clearance at the ends and a balanced appearance on doors and drawers.
• The 3/4 inch projection sets the pull away from the door surface, which helps fingers fit behind the pull without rubbing against the cabinet face during use.
• The 1/2 inch width keeps the pull narrow on the face, which is useful on smaller drawer fronts or narrow rails where wider hardware might crowd edges.
• The polished chrome finish gives a reflective surface, which works well when coordinating with chrome hinges, faucets, or appliance trim in the same area.

Mounting Dimensions And Sunnyside Fit

The center to center distance of 3 inches defines the drilling pattern for this Sunnyside Series pull, which aligns with many standard cabinet boring jigs used in shops. With an overall length of 4 inches, the pull extends beyond the holes so the ends visually anchor the hardware on the cabinet face. The 3/4 inch projection establishes how far the gripping surface stands off from the door or drawer front, which affects how easily hands catch the pull from different angles. Its 1/2 inch width sets how much face area the hardware covers, which matters when aligning multiple pulls in a run so reveals remain consistent. The Belwith Keeler P115-26 designation identifies this exact polished chrome version, which supports matching pulls across multiple cabinets.

Using This Belwith Keeler Pull In Projects

Where The Hickory Hardware Sunnyside Pull Fits

This Hickory Hardware Sunnyside Series pull works wherever a 3 inch center to center cabinet or drawer handle is required, because its mounting pattern is built around that dimension. The pull belongs to the Decorative Hardware & Moldings category under handles and pulls, which places it in typical cabinet, furniture, or built-in applications handled by woodworking trades. Its zinc die cast construction provides a metal body suited to interior cabinet and drawer fronts that see frequent hand contact. With a length of 4 inches, the pull scales well on many standard-width drawer fronts, creating a visible but not oversized handle line. The polished chrome finish matches other polished chrome hardware elements, so a run of cabinets can carry the same finish from door to door for visual continuity. As a Belwith Keeler product, it pairs with other Belwith hardware choices when a coordinated set is desired on a job.

Details That Support Consistent Installation Results

The defined 3 inch center to center measurement supports consistent drilling across multiple fronts, because installers can set stops on a boring jig to that exact spacing and repeat the pattern throughout the project. The 4 inch overall length gives a predictable edge distance from each mounting hole to the end of the pull, which helps align hardware so that pulls line up visually along cabinet rows. A projection of 3/4 inch creates a known stand-off dimension from the door face, which keeps hand clearance uniform on doors and drawers installed side by side. The 1/2 inch width gives a fixed face coverage, which helps layout when aligning pulls relative to panel edges or rail widths. Identifying this pull as part of the Sunnyside Series and as Manufacturer Part P115-26 allows planners to document the exact hardware used, which simplifies reordering the same polished chrome pull for future cabinet additions or service work.

Common Questions About The Sunnyside Chrome Pull

Selecting The Right Sunnyside Pull Size And Finish

The Hickory Hardware Sunnyside Series 3 inch center to center polished chrome pull P115-26 from Belwith Keeler offers a defined 3 inch mounting pattern, a 4 inch overall length, and a 3/4 inch projection, so it suits standard cabinet and drawer layouts that call for metal pulls in polished chrome. For projects using Decorative Hardware & Moldings handles and pulls with a bright finish, this zinc die cast design gives a consistent look across multiple fronts. Selecting this specific Sunnyside Series polished chrome pull allows cabinets, furniture, or built-ins to share the same measured dimensions and finish from piece to piece.