Mending Plates No Screws 2-1/2"L x 5/8"W

Mending Plates For Straightforward Furniture Repair

Mending Plates No Screws 2-1/2 L x 5/8 W from Selby Furniture Hardware is a flat steel mending plate that ties two pieces together wherever extra support is needed. The zinc plated rust resistant steel construction holds up in typical shop or jobsite environments, so joints stay reinforced over time on cabinets, furniture, or light structural framing within its size range. The plate sits flat because the screw holes are not countersunk, keeping the bearing surface broad along the joint. That flat profile helps spread loads along the face of the material instead of concentrating them at a few raised points. With a length of 2-1/2 inches and a width of 5/8 inch, this mending plate suits repairs or new builds where a compact yet useful span is required across a seam.

Key Zinc Plated Mending Plate Details

• The 2-1/2 inch length bridges short joints or cracks, so installers can tie pieces together without crowding nearby hardware or edges, which is helpful in tight cabinet interiors or confined furniture frames.
• The 5/8 inch width gives enough bearing surface along the joint while staying slim, allowing the plate to sit on narrow rails or stretchers without overhanging and interfering with adjacent components.
• Zinc plated rust resistant steel resists corrosion in normal interior woodworking conditions, so the reinforcing plate keeps its integrity over time when used inside cabinets, casework, or furniture assemblies.
• Screw holes are not countersunk, keeping the plate profile uniform across its face, which simplifies layout when the plate must sit flush against flat timber or sheet goods without recessing the holes.
• The Selby Furniture Hardware brand and X997C25U part number identify this specific mending plate, helping shops reorder the same size and material when a consistent repair or production solution is needed.

Installation Behavior Of The Flat Mending Plate

This zinc plated rust resistant steel mending plate installs as a flat fastener across a joint, using the preformed screw holes to secure it to the workpieces. Because the screw holes are not countersunk, the screw heads sit proud relative to the plate surface, which influences where the plate is placed in relation to other components or moving parts. The 2-1/2 inch length works across modest spans in rails, stiles, or panel edges, giving enough distance between screws for a stable connection. Its 5/8 inch width fits on relatively narrow stock, making it suitable for small-section cabinet parts or furniture members where larger plates would overrun the faces.

Using The Selby Mending Plate In Woodwork

Where This Flat Steel Mending Plate Fits Best

This mending plate from Selby Furniture Hardware fits applications where a straight, flat reinforcement is needed across a joint rather than an angled brace. The 2-1/2 inch length allows it to span small separations in cabinet carcasses or furniture frames within its reach. At 5/8 inch wide, it works on slim members such as narrow rails or face-frame parts, avoiding interference with neighboring components while still giving enough width for multiple fasteners. The zinc plated rust resistant steel construction suits indoor woodworking environments, so it can be used inside cabinets, closets, or furniture where moisture exposure is limited to everyday indoor levels. Because the screw holes are not countersunk, this plate is suited to areas where a low-tech, flat plate with visible screw heads is acceptable and functional.

Why These Selby Details Support Repeatable Work

The defined 2-1/2 inch by 5/8 inch size helps installers standardize repairs and reinforcements, since the span and bearing area are predictable every time X997C25U is used. Knowing the screw holes are not countersunk lets fabricators plan for the screw head profile, which can guide choices about which side of a cabinet, panel, or frame will present the hardware. Zinc plated rust resistant steel provides a consistent surface and performance level, so multiple plates in a run behave similarly under normal interior conditions. Having the Selby Furniture Hardware brand and X997C25U part number tied to this exact plate streamlines restocking and specification in shop drawings, reducing mismatches when identical reinforcement is required across several units. This consistency supports efficient workflows in both small repair jobs and volume cabinet production.

Common Questions About X997C25U Mending Plate

Select This Mending Plate For Consistent Repairs

The Mending Plates No Screws 2-1/2 L x 5/8 W from Selby Furniture Hardware offers a defined size, zinc plated rust resistant steel construction, and non-countersunk screw holes that work together as a predictable reinforcing solution. Using the X997C25U part number lets shops and installers call out the same flat plate across drawings and work orders, so joints are reinforced with consistent hardware from one project to the next. For cabinet, furniture, or light framing work that needs a compact flat brace, this zinc plated mending plate from Wurth Baer Supply provides a clear, repeatable option to support your next repair or build.