
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
Panel Buddies rectangular inserts give cabinet panels a controlled support point because each insert is a spacer that holds the panel off the groove over the length of the spacer. This support helps the panel stay centered while still allowing movement because the design maintains a consistent gap where the panel bears on the spacer. The spacers are 1/4 inch by 1/4 inch by 3/4 inch long, so they match common cabinet panel layouts that use 1/4 inch stock. These panel spacers are for use in standard 1/4 inch grooves, so they drop into typical cabinet frame grooves without changing groove dimensions. The rubber material has no oil or silicones to disrupt finishing, so stain, paint, or clear coats can be applied with reduced risk of finish problems at the contact points. The rectangular shape ensures they will not roll around the shop if they get dropped, which keeps handling predictable during production runs.
Panel Buddies panel spacers are for use in standard 1/4 inch grooves, so they match common cabinet frame groove cuts used with 1/4 inch panels. Because each spacer is 1/4 inch by 1/4 inch in section, it nests into the groove profile and presents a flat face to the panel. The 3/4 inch length gives the panel a longer bearing area in each location, so the panel edge sits on a solid rubber strip rather than a small nub. The way these spacers support the panel over the length of the spacer means the panel edge contact is extended, which helps maintain alignment along the groove. At the same time, the design allows maximum expansion and contraction without putting undue pressure on the glue joints, so the frame maintains its glued corners while the panel moves against the rubber.
Panel Buddies rectangular inserts are panel spacers for cabinets that use standard 1/4 inch grooves, so they are applied anywhere a 1/4 inch panel floats in a frame-and-panel construction. Because each spacer is 1/4 inch by 1/4 inch by 3/4 inch long, it fits into the same 1/4 inch groove that accepts the panel edge and creates a positive contact point at that depth. The design supports the panel over the length of the spacer, so each installed piece turns a short section of the groove into a cushioned bearing surface. Since the panel is allowed maximum expansion and contraction without putting undue pressure on the glue joints, these inserts support applications where wood or panel cores move across the seasons while the surrounding frame stays fixed by glue.
The fact that these panel spacers are for use in standard 1/4 inch grooves means shop layouts and tooling that already cut 1/4 inch grooves do not need dimension changes, which keeps groove positioning and panel sizing consistent from job to job. The 1/4 inch by 1/4 inch by 3/4 inch dimensions create a predictable block of rubber that sets a known stand-off when the panel rests on it, which helps keep reveal lines and panel clearances more uniform across a run of doors or panels. Because the panel is allowed maximum expansion and contraction without putting undue pressure on the glue joints, the stress that would otherwise push against the frame corners is taken up at the spacer, which supports long-term joint performance. The rubber material has no oil or silicones to disrupt finishing, so the spacer contact areas do not introduce contaminants that could affect finishes where the panel meets the frame. Finally, the rectangular shape ensures they will not roll around the shop if they get dropped, which supports shop efficiency by keeping small parts controllable on busy benches and floors.
Panel Buddies rectangular inserts are panel spacers for cabinets, supporting the panel over the length of each spacer so the panel can move while the frame and glue joints stay stable.
Panel Buddies panel spacers are for use in standard 1/4 inch grooves, so they sit in the same groove as the panel edge and establish a controlled contact point for support.
The spacers are 1/4 inch by 1/4 inch by 3/4 inch long, which matches typical 1/4 inch groove layouts and provides a longer bearing surface so the panel rests on a stable rubber block.
The design allows maximum expansion and contraction without putting undue pressure on the glue joints, so panel movement is absorbed at the spacer instead of stressing the frame corners.
The rubber has no oil or silicones to disrupt finishing, so finishes applied around the groove can bond normally without spacer material interfering with coating adhesion.
The rectangular shape ensures they will not roll around the shop if they get dropped, which keeps small parts easy to retrieve and reduces time spent chasing round pieces.
Panel Buddies PB265-750XF-10M panel spacers provide a defined way to support cabinet panels because they sit in standard 1/4 inch grooves and match 1/4 inch panel systems. The 1/4 inch by 1/4 inch by 3/4 inch rubber inserts support the panel over their length while allowing maximum expansion and contraction without putting undue pressure on the glue joints. With rubber that has no oil or silicones to disrupt finishing and a rectangular shape that stays put on shop surfaces, these rectangular inserts suit production or shop environments that rely on consistent panel support. Sold in full box quantity only, they align with jobs that need a high count of repeatable panel spacers.
Sold In: 1 Box
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 1 Box | MIPB265-7X50XF-1M Mfr# PB265-750XF-1M | Panel Buddies Rectangular Inserts for Cabinets Rubber Black - 1000 Each | ||||
Sold in: 1 Box | MIPB265-7X50XF-40M Mfr# PB265-750XF-40M | Panel Buddies Rectangular Inserts for Cabinets Rubber Black - 40000 Each |