Power Magnet, 45/64" (10 Pack)

Power Magnet 45/64 10 Pack For Cabinets

Power Magnet 45/64 10 Pack is a Fastcap neodymium cabinet catch that inserts into a 9/16 inch diameter hole in the cabinet frame and provides magnetic holding power at the closing edge. The POWER MAG 18MM, listed as 18mm x 5mm in the SAP description, gives you a compact magnet body that sits shallow in the frame, which helps when working with standard cabinet stock thickness. The web description notes that this high performance neodymium magnet works as part of a two-piece catch system, so you get the magnet in the frame and a steel target on the door. The magnets are identified as a 10 pack, which supports use across a run of doors in the same job without mixing part numbers. Fastcap branding ties this catch to a line focused on shop and cabinet hardware, which keeps selection consistent with other components used in woodworking projects.

Key Cabinet Magnet Details That Help On Site

• The web description states that the magnet inserts into a 9/16 inch diameter hole in the cabinet frame, which gives you a clear drilling size and helps keep hole preparation fast and repeatable on multiple frames.
• The description explains that the cabinet frame hole can be covered using cover caps referenced as FAPHKKMET42-200, which allows you to hide the magnet location and keep the frame face looking clean when appearance is important.
• The SAP description notes dimensions of POWER MAG 18MM as 18mm x 5mm, so the magnet body stays low profile in the frame, which is useful when working near shallow grooves or tight clearances.
• The web description specifies that a 3/8 inch long by 7/16 inch diameter power head screw is inserted into the door to act as the magnetic catch, so the steel screw head becomes the strike for the magnet and simplifies alignment between door and frame.
• The same description clarifies that this screw is sold separately, so the magnet set focuses on the frame-mounted component while letting you match the specified power head screw to your standard fastener sourcing.

Cabinet Frame Magnet Mounting And Door Catch Fit

The web description identifies this Fastcap catch as a high performance neodymium magnet that inserts into the cabinet frame, so the magnet side of the catch is always frame-mounted instead of on the door. The stated 9/16 inch diameter frame hole gives you a single drill size to follow, which keeps layout simple when you are boring multiple frames in a row. The POWER MAG 18MM size listed as 18mm x 5mm means the magnet occupies a relatively shallow depth, so it works well where you want holding force without cutting deep into the stile. The description also points out that a 3/8 inch long by 7/16 inch diameter power head screw in the door acts as the magnetic catch, so you match the screw position to the magnet center for consistent closing.

Using This Fastcap Power Magnet In Cabinet Work

Where This Neodymium Cabinet Magnet Is Applied

The product data describes this item as a high performance neodymium magnet that inserts into a 9/16 inch diameter hole in the cabinet frame, so its primary use is in framed cabinet construction where you want a clean magnetic catch. The SAP description identifies it as POWER MAG 18MM, 18mm x 5mm, which aligns with a compact insert magnet suited to typical face frames and interior partitions. The web description states that a 3/8 inch long by 7/16 inch diameter power head screw is inserted into the door to act as the magnetic catch, so this part is used wherever you can drive that screw into the door edge or stile. The note that the cabinet frame hole can be covered using cover caps labeled FAPHKKMET42-200 explains how this magnet can be used on visible frame faces where you still want a finished look after installation.

Why These Magnet Details Support Repeatable Results

The specified 9/16 inch diameter hole for the cabinet frame means you can standardize one drill bit or boring setup, which speeds repetitive cabinet production and keeps magnet fit consistent from cabinet to cabinet. The POWER MAG 18MM dimension of 18mm x 5mm provides a predictable depth in the frame, so you control how close the magnet sits to the door and maintain uniform closing force across a bank of doors. The description that a 3/8 inch long by 7/16 inch diameter power head screw acts as the door-side catch lets you use a defined target size, which simplifies marking, drilling, and driving for that screw on every door. The reference to cover caps FAPHKKMET42-200 over the frame hole means the visible side of the installation can stay uniform, so finished jobs have consistent appearance even when several magnets are used on the same project.

Practical Questions About POWER MAG 18MM Magnet Use

Selecting This Power Magnet For Cabinet Projects

The product information from Wurth Baer Supply identifies this Fastcap item as a high performance neodymium cabinet catch that inserts into a 9/16 inch frame hole and works with a defined power head screw in the door. Those details give you clear dimensions and mounting roles, which helps match this 18mm x 5mm POWER MAG 18MM to cabinet frames and doors where a compact magnetic catch is needed. When a project calls for a frame-mounted magnet and a screw-based strike on the door, this 10 pack provides a consistent part number to use across the run.