
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
Berenson Dash Series pull is a zinc and acrylic handle with a polished chrome and black finish that brings a defined contrast to cabinet and drawer fronts, giving casework a clean, modern look that aligns across a full run of fronts.
The 3-3/4 inch (96 mm) center to center drilling matches common cabinet boring layouts, so this pull fits many standard handle locations without redrilling, keeping fronts intact when updating hardware on existing installations.
The overall 7-5/16 inch length spans more of the rail, which visually anchors wider drawers and doors, creating a consistent sightline when used across banks of cabinets in a kitchen, bath, or shop setting.
A 1 inch projection brings the grip out far enough from the face of the door or drawer for fingers to wrap comfortably around the pull, helpful when working with thicker fronts or when hands are gloved in a workshop.
The 1/2 inch width and 3/8 inch base dimensions give a slim footprint at the mounting points, so the pull sits neatly on narrow rails while still covering typical previous pull footprints.
The 3-3/4 inch (96 mm) center to center drilling of this Berenson Dash Series pull sets exact hole spacing, which streamlines layout when boring new fronts and guides alignment when matching existing 96 mm pattern hardware.
With an overall 7-5/16 inch length, the pull reaches farther across the facade than a compact tab pull, so alignment can reference door or drawer edges for consistent reveals, reducing the chance of visually uneven hardware rows.
The 1 inch projection defines how far the handle stands off the surface, which influences both grip comfort and clearance around adjacent trim or face frames, especially on tight installations where doors open near walls or tall panels.
A 1/2 inch width and 3/8 inch base dimension concentrate the bearing area at the mounting points, so the pull seats firmly against the face while staying narrow enough for small drawer fronts or rail sections often found in upper cabinets.
The Berenson Dash Series 3-3/4 inch (96 mm) center to center pull functions as a handle for cabinet doors and drawers where a modern, linear profile is preferred, allowing it to be used across kitchens, bathrooms, and built-in storage runs.
Because the pull uses the 96 mm center to center drilling, it fits layouts that already follow that standard spacing, so replacing an older 96 mm pull can keep the existing boring pattern while changing the style and finish to polished chrome and black.
The zinc and acrylic material pairing supports use on residential casework where metal hardware is expected, while the acrylic detail adds contrast that can help define handle position against similarly toned door finishes.
The 7-5/16 inch overall length makes this pull particularly suited to medium and wider drawer fronts, where extra handle span lets users grab closer to either side of the drawer, distributing opening force across a larger section of the drawer face.
The 1 inch projection also works well on doors near thicker edge profiles, where the pull needs to stand proud enough of the face for fingers to clear decorative edges or applied moldings during operation.
With a 1/2 inch width and compact 3/8 inch base, the pull can be laid out on narrow rails such as top drawers or small upper cabinets, maintaining a consistent hardware family across different cabinet sizes in one installation.
The 3-3/4 inch (96 mm) center to center measurement allows installers to use standard drilling jigs, which can speed production work and help maintain straight, level hardware rows across long cabinet runs with repeated hole spacing.
Using a pull that has a 7-5/16 inch overall length with that same 96 mm mounting distance creates a balanced ratio between mounting points and handle length, which improves the visual proportion on many common drawer heights.
The 1 inch projection establishes a repeatable standoff from the cabinet face, so doors and drawers across a project all present handles at the same depth, supporting clean lines when viewed from an angle along the run of cabinets.
A 1/2 inch width and 3/8 inch base dimension mean layout marks around each hole can be reliably covered by the foot of the pull, beneficial when swapping from another 96 mm pull that left minor impressions at the mounting points.
The polished chrome and black finish combination makes hardware placement easier to read because the reflective chrome edge and darker black detail create a visible line against many painted or laminated surfaces under typical room lighting.
The zinc and acrylic construction also keeps the handle profile precisely defined at its edges, so when multiple Berenson Dash Series pulls are aligned, the straight lines across the project remain crisp, which is important for modern cabinet styles.
The Berenson 9746-1000-P pull has a 3-3/4 inch (96 mm) center to center dimension, setting the distance between mounting holes for layout and replacement work.
The pull has a 7-5/16 inch overall length, so it spans a good portion of typical cabinet doors and drawers, giving more grab area and a strong visual line.
This Berenson Dash Series pull has a 1 inch projection, setting consistent clearance for hands between the grip and the cabinet face on doors and drawers.
The Berenson 9746-1000-P pull is made from zinc and acrylic with a polished chrome and black finish, giving a metal feel with a contrasting visual accent.
The pull has a 1/2 inch width and 3/8 inch base dimensions, so it sits with a slim footprint while covering typical mounting marks at the screw locations.
The Berenson Dash Series 9746-1000-P uses M4 screw size, which aligns with common cabinet hardware threading for door and drawer front installations.
The Berenson Dash Series 3-3/4 inch (96 mm) center to center pull from Wurth Baer Supply combines zinc and acrylic construction with a polished chrome and black finish, giving cabinets a defined modern line that coordinates across doors and drawers.
With a 7-5/16 inch overall length, 1 inch projection, 1/2 inch width, and 3/8 inch base dimensions, this pull aligns with standard 96 mm drilling patterns while delivering consistent clearance and coverage on cabinet faces.
For projects built around the 96 mm center to center standard, the Berenson 9746-1000-P pull provides a straightforward way to coordinate cabinet hardware style and measurements across new or updated installations.
Sold In: 1 Each