HandiTRIM indented edge cap is a trim extrusion designed to finish off a Handi br WALL installation, so Wallscape slatwall edges and corners present a continuous surface. The 96 inch length gives you long, uninterrupted runs along slatwall edges, which helps reduce joints that might draw the eye on finished walls. Its taupe color matches available Wallscape colors, so the transition from panel to trim stays visually consistent across the wall. The 3/4 inch width and 3/4 inch height profile are sized to fit typical Wallscape slatwall edge situations, creating a defined termination where panels meet open wall. As a slatwall accessory, the cap fits corners or edges as needed to deliver a finished, gap-less look to Wallscape slatwall, which matters in closets, garages, or storage walls where a clean, professional appearance is part of the job expectation.
This HandiTRIM indented edge cap is specified at 96 inches long, which aligns with extended stretches of Wallscape slatwall so you can span most wall sections with single pieces. The 3/4 inch width and 3/4 inch height profile establish a compact but defined edge, so the trim sits neatly at panel boundaries without dominating the wall surface. Because the extrusion fits corners or edges as needed, the same profile works at panel perimeters and inside corners, helping maintain consistent geometry around the entire Wallscape layout. As part of the Handi br WALL installation, this trim extrusion works with Wallscape slatwall to present a continuous, gap-less finish along perimeter edges.
This HandiTRIM indented edge cap is intended for use wherever Wallscape slatwall panels end at an exposed boundary or turn a corner, because it fits corners or edges as needed for a finished appearance. In a Handi br WALL installation, the extrusion runs along panel perimeters, covering the transition between slatwall and adjacent wall surfaces so the edge reads as a deliberate border. The 96 inch length suits common closet, garage, or storage wall spans, so installers can run trim from floor to near-ceiling or across wide wall sections without frequent joints. Its taupe color is part of the range of available Wallscape colors, which supports visually consistent layouts when matching taupe panels are used throughout the wall system.
The 96 inch L x 3/4 inch W x 3/4 inch H profile offers a predictable, repeatable geometry, so installers can plan clear edge lines and maintain the same reveal around every Wallscape panel. Because the extrusion is designed specifically to finish off the Handi br WALL installation, it interfaces with Wallscape slatwall to provide a gap-less look, which reduces small irregular openings where panels meet surrounding walls. The ability to fit both corners and edges means one HandiTRIM profile carries through the entire job, which helps keep trim style uniform around inside corners, outside corners, and straight terminations. Being available in all available Wallscape colors gives this taupe version a coordinated role in the system, so the trim can visually disappear into the Wallscape layout or define edges with a controlled color band, depending on panel selection.
The HandiTRIM indented edge cap is a trim extrusion that finishes off the Handi br WALL installation, so Wallscape slatwall corners and edges present a finished, gap-less look on completed walls.
The HandiSOLUTIONS HST2096E edge cap is 96 inches long, which allows installers to cover extended slatwall runs with fewer joints along panel edges.
This Wallscape slatwall trim extrusion measures 96 inches L x 3/4 inch W x 3/4 inch H, creating a compact edge profile that defines slatwall boundaries.
This HandiTRIM slatwall accessory is used at corners or edges of Wallscape slatwall, so exposed panel boundaries transition cleanly to adjacent wall areas.
The taupe edge cap is available as part of the Wallscape color range, so it can match taupe Wallscape panels for a consistent, coordinated wall appearance.
This trim is specifically offered to finish off the Handi br WALL installation, providing a gap-less look that supports a clean, professional Wallscape slatwall finish.
The HandiTRIM indented edge cap, HandiSOLUTIONS part HST2096E, gives Wallscape slatwall installations a defined, gap-less edge treatment using a 96 inch L x 3/4 inch W x 3/4 inch H taupe extrusion. When a Handi br WALL installation calls for finished corners or edges, this trim extrusion supplies a coordinated way to close panel boundaries and present a clean, continuous Wallscape surface.
Sold In: 1 Each