Berenson Studio Series 10-1/16" (256 mm) Center to Center Stainless Steel Pull, - 2025-90SS-P

Berenson Studio Stainless Pull For Cabinet Runs

Berenson Studio stainless steel pull gives cabinets a straight, modern grip that suits professional shops and serious DIY work. The pull is part of the Studio collection, so the profile stays consistent across a project where matching hardware matters. The center to center measurement of 10-1/16 inches, or 256 mm, sets hole spacing that works well on wider drawers and tall doors, helping align longer fronts visually. Overall length of 10-5/8 inches adds a little overhang beyond the drilled points, which can help hands clear door edges in daily use. Stainless steel material provides a solid feel in the hand, which supports repeated opening on busy kitchen or shop cabinets. A stainless steel finish keeps the color and sheen uniform with other stainless components in the space, which helps maintain a clean run of hardware.

Key Studio Pull Details That Support Workflow

• The Studio collection identification ties this pull to other Studio pieces, which helps keep a project visually consistent when multiple sizes are used across a bank of cabinets.
• Stainless steel material creates a firm, rigid handle, which supports frequent use on doors and drawers in active residential or light commercial environments.
• The stainless steel finish keeps the appearance neutral and metallic, which helps this pull blend with common appliance finishes and hinge selections on a job.
• A length or diameter listed as 10-5/8 inches defines the outer span of the pull, which helps with laying out spacing on wide drawer fronts and tall doors.
• The 10-1/16 inch, or 256 mm, center to center dimension sets exact hole spacing, which is critical when drilling through finished cabinet faces or replacing an existing pull.
• A projection of 1-7/16 inches sets how far the pull stands off the door, which gives finger clearance while keeping the handle close enough to avoid catching on clothing.
• A width of 9/16 inch specifies the gripping bar thickness, which affects how the pull feels in the hand and how it lines up proportionally on face frames or slab fronts.
• Screw size listed as 8-32 x 1 inch indicates the thread and length used, which matters when matching to pre-tapped inserts or planning drill depth in dense materials.

Mounting And Dimension Details For Berenson Pull

The Berenson Studio Series 10-1/16 inch center to center stainless steel pull is sized for runs where longer hardware is needed on doors and drawers. The 256 mm center to center spacing lets installers use metric or imperial layout tools while keeping hole locations precise across multiple fronts. Length listed at 10-5/8 inches means the pull extends slightly past the boring pattern, which helps align edges with rail lines or stile reveals. A projection of 1-7/16 inches sets the stand-off depth, allowing fingers to wrap behind the bar without driving the pull too far into the room. Width of 9/16 inch defines the bar thickness, which influences how the pull sits against narrow rails or full-overlay slab faces. Screw size 8-32 x 1 inch establishes the fastening thread and reach into the door or drawer, which supports secure mounting in typical cabinet materials.

Using This Studio Pull On Cabinets And Drawers

Where The 256mm Studio Pull Works Best

The Studio collection stainless steel pull is designed as decorative hardware for cabinet applications where a straight, contemporary handle is preferred. With a 10-1/16 inch, or 256 mm, center to center dimension, this pull suits larger drawers or taller cabinet doors that benefit from a longer grip point. The stainless steel material allows it to serve on kitchen, bath, or shop cabinets that see regular opening and closing. A stainless steel finish helps the pull coordinate with hinges, appliances, or other stainless elements on the project, which supports a unified appearance across the room. The 9/16 inch width keeps the bar visually narrow enough for face-frame cabinets yet substantial enough for full-overlay or slab doors. Length at 10-5/8 inches helps balance wide drawer fronts, giving a clear hand hold across the working zone.

Why These Dimensions Support Consistent Installation

The 256 mm, or 10-1/16 inch, center to center specification on the Berenson Studio Series 2025-90SS-P pull sets a repeatable boring pattern, which is valuable when drilling multiple fronts on a production job. Having the length defined at 10-5/8 inches means layout lines can be referenced from the bar ends for even reveals from door edges. Projection of 1-7/16 inches keeps enough space behind the handle for fingers, which reduces contact with the cabinet face during use and can help limit finish wear around the grip zone. The 9/16 inch width produces a consistent bearing surface on the door or drawer face, which helps distribute hand force over a stable area. The 8-32 x 1 inch screw size pairs the pull with a common cabinet fastener specification, which simplifies matching drill sizes and tap patterns across a job using this model.

Common Questions About The 2025-90SS-P Studio Pull

Selecting This Studio Pull For Your Next Run

The Berenson Studio Series 10-1/16 inch center to center stainless steel pull combines defined dimensions with straightforward styling for cabinet projects. With stainless steel material and finish, 256 mm mounting spread, 10-5/8 inch overall length, 1-7/16 inch projection, and 9/16 inch width, the 2025-90SS-P model offers known sizing that fits planning for larger drawers and doors. For jobs that need a consistent Studio collection look and a clearly specified pull layout, this stainless steel handle is a practical option to put into your next cabinet run.