
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
Berenson Hillcrest pull 128mm center to center describes a cabinet handle from the Berenson Hillcrest Series built for cabinet and furniture doors or drawers. The pull has a 5-1/16 inch center to center dimension, so the mounting holes on the cabinet front are spaced on that measurement for a straight swap where that drilling already exists. The 6-5/8 inch overall length gives the hand a little more bar to grab, which helps when opening wider or heavier fronts. A 1-1/8 inch projection stands the pull off the face of the cabinet, giving fingers room behind the handle during use. With a 5/8 inch width, the profile stays slim on the face while still presenting a defined edge to pull against in daily operation.
The Hillcrest Series pull has a 5-1/16 inch center to center dimension, so the two mounting points land on that fixed spacing when laying out or aligning holes on doors and drawers. That measurement is central to planning runs of cabinets with multiple pulls in a line. The 6-5/8 inch overall length defines how much bar extends across the face, affecting both proportion on narrower fronts and how far the handle reaches toward the center on wider ones. A projection of 1-1/8 inch provides clearance between the pull and the door surface, which influences how easily fingers can hook behind the bar. The 5/8 inch width sets how much visual band of metal shows on the face, affecting both grip edge and how the hardware reads against the cabinet design.
The Berenson Hillcrest Series pull is categorized as decorative hardware under handles and pulls, positioning it for cabinet and furniture door or drawer fronts where a handle is required. Its 5-1/16 inch center to center drilling makes it suitable wherever that hole spacing is planned, from kitchen cabinets to built-ins, because the measurement sets the mounting points. The Verona Bronze finish helps the pull act as a visible design feature on wood or painted surfaces, giving contrast on lighter cabinetry and a coordinated tone on darker finishes. With a 6-5/8 inch length, the pull spans a noticeable section of the front, which can visually balance medium-size doors and provide a comfortable reach point on wider drawers or panels that open with more resistance.
The 5-1/16 inch center to center dimension on this Berenson Hillcrest pull provides a repeatable drilling pattern, which helps maintain alignment across banks of doors and drawers using the same handle. When that measurement is applied across a run, the 6-5/8 inch overall length ensures each pull presents a consistent visual footprint, so edges of handles line up predictably relative to door rails and drawer fronts. The 1-1/8 inch projection sets a uniform stand-off from the cabinet surface, which keeps finger clearance consistent from piece to piece and supports a similar hand feel on every opening. The 5/8 inch width keeps the bar slim enough to sit neatly on narrow stiles while still giving a defined edge for fingers to grip, helping reduce slipping during repeated daily use. Because the material is zinc with a Verona Bronze finish, multiple pulls from the same collection maintain a matching appearance, supporting coherent hardware runs throughout kitchens, baths, or casework installations.
The Berenson Hillcrest Series pull has a 5-1/16 inch center to center dimension, which sets the spacing between mounting holes on cabinet doors or drawers.
The Hillcrest pull measures 6-5/8 inches in overall length, so it spans a noticeable section of the cabinet front for both grip and visual balance.
The Berenson Hillcrest pull has a 1-1/8 inch projection, creating space between the handle and the cabinet face for fingers to fit behind the bar.
The Hillcrest Series pull is made from zinc with a Verona Bronze finish, giving a metal base that supports the darker bronze appearance on cabinet fronts.
The 2070-10VB-P pull is part of the Camber collection and the Hillcrest Series from Berenson, aligning it with related decorative hardware pieces.
The Berenson Hillcrest cabinet pull has a width of 5/8 inch, affecting how much metal band shows on the cabinet face and how the edge feels in the hand.
The Berenson Hillcrest Series 5-1/16 inch center to center Verona Bronze pull combines a defined 5-1/16 inch drilling pattern, 6-5/8 inch overall length, and 1-1/8 inch projection for predictable cabinet handling. With its zinc construction, Verona Bronze finish, and 5/8 inch width, it offers a coordinated option when a Hillcrest Series handle with these dimensions fits the layout. For projects using this style and measurement set, this pull provides a consistent hardware choice.
Sold In: 1 Each