Berenson Vested Interest Series 5-1/16" (128 mm) Center to Center Vintage Nickel Pull, - 2370-1VTN-P
Description
Berenson Vested Interest Pull For Cabinet Projects
Berenson Vested Interest pull describes a cabinet handle from the Vested Interest collection that uses a 5-1/16 inch (128 mm) center to center, giving you a predictable drilling layout for new cabinets or straightforward swap-out on existing fronts. The pull is made from zinc, which provides a solid metal body suited to everyday cabinet use in kitchens, baths, or built-ins. A vintage nickel finish covers the pull, adding a muted metallic look that supports traditional or transitional door and drawer styles. Overall length is 6 inches, so the handle spans a bit beyond the hole spacing, giving you good hand clearance across wider drawer faces. A projection of 1-3/16 inches sets the grip away from the face, which helps fingers wrap behind the pull. Width is 5/8 inch, creating a slender profile that fits cleanly on narrow stiles and rail sections.
Key Berenson Pull Details That Support The Job
- The 5-1/16 inch (128 mm) center to center drilling dimension aligns the mounting holes, which simplifies layout when installing multiple pulls across cabinet runs.
- The 6 inch overall length gives extra handle span beyond the fastener points, which helps the pull visually balance on both narrow and standard drawer fronts.
- The 1-3/16 inch projection establishes working clearance between the pull and the cabinet surface, which supports a comfortable grip without knuckles contacting the door.
- The 5/8 inch width keeps the pull profile slim, which lets you place it on tight rail areas or smaller doors without crowding surrounding edges.
- The zinc material builds the pull from metal, which provides a rigid feel at the hand and responds well in typical residential cabinet environments.
- The vintage nickel finish sets a soft metallic appearance, which coordinates with many hinges and fixtures that use similar toned finishes.
Installation Dimensions For Consistent Pull Placement
The center to center size of 5-1/16 inches (128 mm) defines the hole spacing for this pull, setting the key measurement for drilling or reusing cabinet fronts. With a 6 inch overall length, the pull overhangs the hole spacing slightly, so the ends extend past the screw locations for a finished look. Projection at 1-3/16 inches fixes how far the pull stands off the face, affecting where the hand lands as you open doors or drawers. Width at 5/8 inch sets the front face size of the pull, which influences how it fits on narrower drawer rails and door frames during layout.
Using The Vested Interest Pull In Cabinet Work
Where This Vintage Nickel Pull Fits Best
The Vested Interest collection identity ties this handle into Berenson cabinet hardware families, which helps keep styling consistent across a room of doors and drawers. The 5-1/16 inch (128 mm) center to center spacing suits cabinets planned around metric drilling patterns, so it works in layouts that specify 128 mm hardware runs. With a 6 inch overall length, this pull is sized for many base cabinet drawers and tall wall doors where a moderate-length handle looks in scale. The 5/8 inch width keeps the pull from visually overpowering smaller fronts, which is useful on narrow bath vanities or utility cabinets that still use the same drilling size. Zinc construction gives the handle a metal base, which supports cabinet projects that call for metal pulls rather than non-metal alternatives.
Details That Support Repeatable Cabinet Results
The 5-1/16 inch (128 mm) center to center dimension standardizes the mounting layout, which helps keep handles in line when you repeat the drilling across large banks of doors and drawers. A projection of 1-3/16 inches sets consistent finger clearance from one cabinet face to the next, which supports uniform feel as doors and drawers are operated. The 6 inch length paired with 5/8 inch width creates predictable proportions, which helps you plan handle placement relative to door edges and panel reveals. A vintage nickel finish applied over zinc presents the same surface look across each pull, which supports visual continuity on face frames and full-overlay fronts. The manufacturer part number 2370-1VTN-P identifies this exact configuration, which matters when you need future orders to match existing installations.
Common Questions About This Berenson Cabinet Pull
What is the center to center size on this pull?
The pull has a 5-1/16 inch (128 mm) center to center dimension, which sets the distance between mounting holes for drilling or matching existing cabinet fronts.
How long is the Berenson Vested Interest pull overall?
The pull length is 6 inches, so the handle extends slightly beyond the 5-1/16 inch hole spacing to give more hand contact area and visual coverage on the front.
What projection does this cabinet pull provide from the door?
The pull has a 1-3/16 inch projection, establishing space between the handle and cabinet surface for fingers to grip as doors and drawers are operated.
How wide is the face of this vintage nickel pull?
The pull width is 5/8 inch, giving a slim face that works on narrower rails or smaller doors without taking up excessive front surface.
What material is used for this Berenson handle?
The handle is made from zinc, providing a metal body suited to regular cabinet use wherever a metal pull is desired on doors or drawers.
What finish is on the 2370-1VTN-P pull?
The pull uses a vintage nickel finish, giving a muted metallic tone that coordinates with other vintage nickel cabinet hardware and fixtures.
Select This Pull For Matching Cabinet Layouts
The Berenson Vested Interest Series 5-1/16 inch (128 mm) center to center vintage nickel pull ties a known drilling dimension to a 6 inch overall length, which supports consistent cabinet layouts. Zinc construction with a vintage nickel finish supplies a metal handle that visually coordinates where similar finishes are already in place. Center to center, projection, and width are clearly defined, which lets you match this pull across new cabinet installations or when repeating the same hardware style on additional projects. For cabinet runs planned around 128 mm spacing and a vintage nickel look, this pull aligns measurements and appearance in one part.