2-1/8" x 3/64" Radius Router Bit for Edge Banding, 5/16" Shank

2-1/8 x 3/64 Radius Router Bit For Clean Banding

2-1/8 x 3/64 radius router bit describes a Festool profiling router bit sized to cut a 1 mm radius, so installers get a small, consistent roundover on matching edge banding without guessing at the profile. This bit is designed for use with the Festool MFK 700 Trim Router, so it integrates into that specific trim routing setup you already run on site or in the shop. Festool identifies this tool as part number 499811 and classifies it as a router bit in the profiling category, which helps match it to technical documentation, service parts, and routing operations that call out that exact specification.

Key Edge Banding Router Bit Details For Pros

• The bit is specified as 2-1/8 inches by 3/64 inch with a 5/16 inch shank, so the cutting geometry and shank size are set for controlled profiling passes in compatible collets.
• A 1 mm radius cutting profile is built into the bit, shaping a consistent small roundover that eases sharp banding edges while keeping a tight, modern look on casework.
• The router bit is designed for 3 mm wood edge banding, so the cutting path tracks the banding thickness instead of cutting too shallow or too deep along the face.
• The same bit is also intended for 3 mm plastic edge banding, so one cutter can handle both common banding materials across laminate or melamine projects.
• Festool classifies this tool as a profiling router bit, so its geometry is tuned to cut shaped edges rather than performing general straight trimming passes on panels.
• The product is individually packed from Festool, so each bit is protected as a single unit between storage, transport, and setup at the router table or trim station.

Edge Banding Router Bit Setup And Fit

The Festool 2-1/8 x 3/64 radius router bit is built around a 5/16 inch shank, so it fits collets matched to that size on the Festool MFK 700 Trim Router for secure gripping and low runout during edge work. Its 1 mm radius profile is sized for 3 mm banding, helping the cutting edges follow the banding height instead of wandering onto the panel surface when the trim router is guided along cabinet parts. Because the bit is tied directly to the MFK 700 trim router system and the KA65 edge banding context in Festool documentation, it lines up with existing jigs and fences that reference that platform for repeat jobs.

Using This Radius Router Bit In Edge Banding Work

Router Bit Performance On 3 Mm Edge Banding

This Festool router bit is described specifically as a router bit for edge banding, so its cutting profile is tuned around standard banding workflows instead of generic profiling. The 1 mm radius is set to produce a small roundover on 3 mm wood edge banding, so the cut softens the transition at the edge without removing too much material or changing the visual thickness of the band. When used on 3 mm plastic edge banding, the same radius profile shapes the plastic edge to match wood runs, so mixed-material installations across a job can hold a consistent edge detail. With overall dimensions of 2-1/8 inches by 3/64 inch, the body and cutting width are sized to keep the cut focused on the banding layer, which matters when working close to finished veneer or laminate faces.

Rotatable Cutters For Extended Service Life

The cutters on this Festool radius router bit can be rotated, and that design provides four new cutting surfaces before replacement is needed, so the same tool body stays in service across multiple edges and jobs. Each time a cutting edge wears, the installer can index to a fresh edge, so the bit maintains a sharp 1 mm radius profile instead of gradually leaving burnished or chatter-prone surfaces on banding. Because the web description highlights that rotating the cutters prolongs service life, the bit supports longer intervals between purchases while preserving the defined 1 mm radius that matches earlier passes on the same project. As a result, the router bit helps keep edge detail consistent from cabinet to cabinet, even as individual cutting edges are cycled through their four positions over time.

Buyer Questions About This Festool Edge Banding Bit

Select This Router Bit For Radius Edge Banding

The Festool 2-1/8 x 3/64 radius router bit for edge banding is specified for 3 mm wood or plastic banding, so it directly supports common casework edge treatments. Its 1 mm radius profile and 5/16 inch shank are matched to the Festool MFK 700 Trim Router platform, which keeps fit and cutting geometry aligned with that tool. With rotatable cutters providing four fresh edges, this router bit keeps its defined radius cut active over many linear feet of banding. Use this Festool 499811 profiling router bit whenever a controlled, repeatable radius on 3 mm edge banding is required.