Euro door stop bumper from Fastcap is a soft rubber door and drawer bumper designed for cabinet and furniture doors that need a controlled stop point. Constructed of soft rubber, this stop cushions the contact point as the door closes, which helps reduce impact on the work surface over repeated use. The clear material keeps the stop visually unobtrusive on light or dark finishes, which supports clean-looking installations in visible cabinet runs.
The door stop bumper is 9/16 inch in diameter, giving a broad contact area against the door edge so the load is spread rather than concentrated on a single point. The bumper is 5/16 inch tall, so it creates a defined stand-off between the door and the case, which helps maintain consistent spacing where an inset or precise gap is part of the design. This Euro-style stop is part of Fastcap's door and drawer bumpers category, so it fits naturally into hardware layouts where controlled door travel is required.
This Fastcap Euro door stop bumper uses an off center screw hole, allowing the stop to be rotated to varied distances from the door for easy adjustability once mounted. Because the mounting point is offset, rotating the bumper changes how far the soft rubber face projects into the door swing, which lets the installer fine-tune where the door lands. This helps dial in the final resting position of the door relative to the cabinet front when a specific inset or reveal is desired.
The combination of 9/16 inch diameter and 5/16 inch height works with the off center mounting to give a predictable adjustment range around the screw. As the bumper turns, the edge of the rubber moves closer to or further from the hinge side contact, which can be used to correct small alignment differences between doors. This adjustability is built into the part, so the stop itself provides a way to tune door position without changing other components.
The clear Euro door stop bumper is well suited to cabinet and furniture work where doors need a defined stop point against a case or frame while keeping hardware visually discreet. Its classification as a door and drawer bumper places it naturally on hinged cabinet doors that close against a face frame or panel, as well as similar applications on work surfaces and tables in the same category. The clear soft rubber material allows the stop to be used on both painted and woodgrain surfaces without strongly altering the appearance of the finished face.
The 5/16 inch tall profile establishes a consistent stand-off, so it supports layouts that depend on an even gap between the door edge and the structure it lands against. The 9/16 inch diameter provides enough surface to contact typical cabinet door thicknesses at a reliable point, which helps create repeatable results across a run of doors using the same model number. Because it is a Euro door stop style bumper, it aligns with hardware plans that follow European cabinet standards for controlled door travel, bringing a predictable stop position into those assemblies.
The off center screw hole is central to how this bumper helps achieve repeatable door alignment. By placing the mounting point away from the center, Fastcap allows the installer to rotate the bumper until the soft rubber face meets the door exactly where needed, which lets the stop fine-tune the resting position. This is especially useful when small variations exist between cabinet openings, since the same bumper can be turned slightly in each location to match the desired stop point.
As the 9/16 inch diameter bumper turns around the screw, the 5/16 inch tall edge traces a small arc that changes the effective projection toward the door, which gives a smooth adjustment range rather than a single fixed position. This design means the stop can help correct minor differences in how far individual doors close, allowing a row of cabinet fronts to share a more uniform look. The soft rubber material then cushions that precisely adjusted contact point, so the door continues to land where set while the impact remains controlled during regular use.
The Euro door stop bumper is constructed of soft rubber, which cushions the closing contact point and helps reduce impact on cabinet doors and cases over repeated openings and closings.
The Euro door stop bumper is 9/16 inch in diameter and 5/16 inch tall, creating a defined contact area and stand-off distance for doors landing against the stop.
The off center screw hole allows the bumper to be rotated to varied distances from the door, so the installer can adjust where the soft rubber face stops the door.
This Fastcap part is classified as a door and drawer bumper, so it is intended for use where cabinet doors or drawers need a defined, cushioned stop point.
The clear color keeps the bumper visually low profile against different finishes, which supports projects where functional stops should remain unobtrusive on the cabinet face.
The manufacturer part number is EURO DOOR 10 CLEAR, which identifies this specific clear soft rubber Euro door stop bumper from Fastcap.
The Fastcap Euro door stop bumper, clear, combines soft rubber construction, a 9/16 inch diameter face, and 5/16 inch height with an off center screw hole for rotational adjustment. Those details provide a cushioned, adjustable stop point that helps set where cabinet doors land while maintaining controlled contact. When a project calls for a clear, Euro-style door and drawer bumper with fine-tuning built into the part, this EURO DOOR 10 CLEAR model aligns directly with that cabinet hardware need.
Sold In: 1 Package