Doellken PVC Edgebanding 15/16" x 1 mm, 30228UM , 300', 30228UM 1540 10

PVC Edgebanding For Matching Tete-a-Tete

PVC edgebanding, in color 30228UM Tete-a-Tete, finishes exposed edges so they visually match the Tafisa M2001Y Tete-a-Tete VIVA laminate, which keeps cabinet and panel projects consistent from face to edge. This edge banding is classified as PVC Edgebanding and Edge Banding, so it is suited for edging furniture, cabinetry, and other laminated casework that uses the matching laminate surface. The 0.018 thick construction provides a defined edge without adding bulk, which helps keep overall panel dimensions close to design size. The 15/16 inch width covers standard panel thicknesses with a bit of overhang for trimming, which supports clean routing or knifing operations. A 300 foot roll format supplies length for multiple doors, drawer fronts, or panels in a single color run.

Key Edge Banding Details For Project Planning

• The 15/16 inch width gives coverage across common board thicknesses, allowing installers to trim back to a flush edge for a finished look on cabinet sides and fronts.
• The 0.018 thick PVC profile keeps the edge slim while still defining the perimeter, which helps maintain a neat transition from the Tafisa M2001Y Tete-a-Tete VIVA face to the edge.
• The 300 foot roll length provides continuous material for longer runs, reducing color breaks and helping maintain visual consistency across banks of cabinets or panels.
• The color 30228UM Tete-a-Tete is specified as a laminate match to Tafisa M2001Y Tete-a-Tete VIVA, so the edge color aligns with that surface choice for coordinated installations.
• The manufacturer part number 30228UM-1540-10 identifies this exact thickness, width, and color combination, which simplifies reordering the same match for follow-up jobs or repairs.

Dimensions And Format That Support Installation

The 15/16 inch width on this PVC edgebanding gives installers enough material to center over a panel edge and trim both sides, which helps achieve a straight, chip-free finished edge. Its 0.018 thick profile works well when a lower build is preferred, making it suitable where a subtle edge line is desired next to Tafisa M2001Y Tete-a-Tete VIVA laminate. The 300 foot roll format supports feeding through edgebanders or manual application over many parts, which can streamline setup and minimize color variation across a project. As a PVC Edgebanding product, it integrates into typical edge processing workflows used by professional woodworking shops.

Using Tete-a-Tete PVC Edgebanding In Projects

Where This PVC Edgebanding Is Typically Applied

This PVC edgebanding, categorized as Edgebanding & Surfacing and Edge Banding, is suited for finishing exposed edges on laminated components that use Tafisa M2001Y Tete-a-Tete VIVA. The 15/16 inch width allows use on standard casework sides, shelves, and doors while leaving enough margin for trimming operations, which is helpful when processing cabinet runs or commercial fixtures. Because the color 30228UM Tete-a-Tete is specified as a laminate match to Tafisa M2001Y Tete-a-Tete VIVA, it supports applications where a coordinated appearance between the flat laminate surface and the edge is essential, such as reception desks, kitchen cabinetry, or panel systems. The 300 foot roll length provides coverage for multiple components in a single project color scheme, which supports consistent edges from part to part.

Why These Edge Banding Details Matter On The Job

The 0.018 thick PVC construction contributes to a fine, controlled edge profile, which can reduce the visual bulk at door and drawer fronts while still clearly defining the boundary of Tafisa M2001Y Tete-a-Tete VIVA surfaces. Having a 15/16 inch wide band gives fabricators room to align the strip accurately on the substrate, which can reduce rework caused by misalignment during edgebanding. The specified laminate match to Tafisa M2001Y Tete-a-Tete VIVA means the 30228UM Tete-a-Tete color is selected to coordinate with that design, helping shops deliver panels where faces and edges appear planned as a single finish. The manufacturer part number 30228UM-1540-10 uniquely identifies this combination of PVC Edgebanding thickness, width, color, and roll length, which helps maintain continuity when repeating a successful specification across multiple jobs or job phases.

Common Questions About Doellken PVC Edgebanding

Select This Roll For Tete-a-Tete Edges

Choose this Doellken Woodtape PVC edgebanding, color 30228UM Tete-a-Tete, when edging panels finished in Tafisa M2001Y Tete-a-Tete VIVA so faces and edges coordinate. The 0.018 thick, 15/16 inch wide, 300 foot roll format supports shop runs where repeated, consistent edging is required in a dedicated laminate match. Using the defined manufacturer part number 30228UM-1540-10 directly ties purchasing to this exact thickness, width, color, and roll length for ongoing cabinetry or casework programs.