Berenson Metro Series Pull For Cabinet Runs

Berenson Metro Series pull gives you a straight-line cabinet handle designed around an 8-13/16 inch center to center mount, so you can line up handles accurately across doors and drawers in the same drilling pattern. This Metro 1 collection pull is made from zinc, which provides a solid metal feel while keeping weight manageable for typical cabinet and furniture fronts. The polished chrome finish reflects surrounding surfaces, helping the pull visually tie in with other chrome decorative hardware on the job. The overall length of 9-1/4 inches spans more of the door or drawer front, which helps visually balance wider faces. A projection of 1-3/8 inches stands the pull off the surface enough to grab with fingers from above or below. The 3/8 inch width presents a slim front edge that keeps the look modern while still giving enough bearing surface for the hand.

Key Metro Pull Details For Cabinet Work

• The 8-13/16 inch center to center dimension gives you a fixed drilling layout that matches standard 224 mm boring, which helps streamline jig setup across multiple cabinet fronts.
• The 9-1/4 inch overall length lets this pull span a wider portion of the panel, which supports visual alignment when you are running handles across banks of drawers.
• The 1-3/8 inch projection sets the pull out from the face, which creates finger clearance between the handle and the cabinet surface during daily use.
• The 3/8 inch width keeps the front profile slim, which maintains a clean, contemporary look on modern cabinet and furniture designs.
• The polished chrome finish presents a bright, reflective surface, which coordinates with other chrome decorative hardware components in the same space.
• The zinc material provides a metal construction, which supports a consistent feel from pull to pull across matching installations.

Mounting Dimensions That Guide Hole Layout

The center to center measurement of 8-13/16 inches, matching the 224 mm spec, anchors how you lay out your boring pattern for this Berenson Metro Series pull. That fixed spacing lets you use metric or imperial jigs without reworking measurements between doors and drawers. The overall length of 9-1/4 inches gives you a clear edge reference when positioning the pull on wider faces, so you can keep reveals and overhangs consistent from cabinet to cabinet. With a projection of 1-3/8 inches off the surface, the handle stands far enough out that hand clearance is predictable when you locate it near edge profiles or decorative trim. The 3/8 inch width defines the visible bar thickness, which matters when you are aligning this pull visually with other narrow-format handles in the same room.

Using This Metro Pull In Cabinet Projects

Where The 8-13/16 Inch Metro Pull Fits Best

This Berenson Metro Series pull, with its 8-13/16 inch center to center dimension, fits runs where you are standardizing on 224 mm drilling across a project. That measurement aligns with common long-pull layouts, so it works on both cabinet doors and wider drawers that benefit from extended grip points. The 9-1/4 inch overall length makes the pull well suited to medium and large fronts, where a short handle would look undersized against the face frame or full-overlay panel. Because the pull is 3/8 inch wide, it pairs visually with other slim hardware, which helps maintain a unified line when handles are repeated across upper and lower cabinets. The polished chrome finish places this pull in projects that already use chrome decorative hardware, so it can tie together hinges, knobs, and other chrome-finished components.

Details That Support Consistent Cabinet Results

The specific 8-13/16 inch center to center value on this Metro 1 zinc pull supports repeatable boring because you can set up drilling equipment once for 224 mm spacing and carry that through the entire job. That consistency reduces layout variation between door and drawer fronts, which keeps handle lines straight when cabinets are viewed as a group. The 1-3/8 inch projection contributes to day-to-day usability by giving the hand space behind the bar, so the pull can be grasped from multiple angles without knuckles contacting the door or drawer face. The 3/8 inch width affects how the handle feels in the fingers, providing a defined edge without adding bulk that might conflict with tight reveals or adjacent hardware. The zinc construction supports a uniform weight and feel, so every pull in the run behaves the same when fronts are opened and closed.

Common Questions About The Metro Series Pull

Selecting This Pull For Your Next Cabinet Run

This Berenson Metro Series pull in the Metro 1 collection combines an 8-13/16 inch center to center mount with a 9-1/4 inch length, so it fits projects built around 224 mm drilling and wider fronts. The zinc construction with a polished chrome finish aligns with chrome decorative hardware, helping you maintain a consistent look from cabinet to cabinet. With a 1-3/8 inch projection and 3/8 inch width, the pull balances finger clearance and a slim profile. Put this model into your layout when those dimensions and finish match the cabinet run you are building.