Dynapro 3D Left-Hand Front Locking Device with Flange

Dynapro 3D Left-Hand Front Locking Device Use

Dynapro 3D left-hand front locking device is a Grass America drawer-front locking and adjustment component designed for Dynapro drawers, so installers can set and secure the left side of the drawer front with predictable control. The 3D version provides 2D or 3D adjustment for drawers, which supports both basic alignment and more precise three-way tuning when projects call for tighter reveals. It is specified for standard width or inset drawers, giving flexibility to use the same part number across different face styles on a job. A minimum inside drawer width of 5-7/8 inches, or 150 mm, is required, so the drawer box must be sized to that interior opening for the device to function correctly. The part uses lightweight, high strength material, so it adds minimal load to the drawer while still holding adjustments under normal use.

Key Dynapro Front Clip Details For Projects

• The device is a left-hand front locking device with flange, which locates and secures the left drawer front connection point while the flange provides a stable mounting edge on the drawer member.
• Height adjustment range of plus 3.5 mm allows the drawer front to be shifted upward, helping align top gaps and match adjacent fronts across a bank of drawers.
• Side adjustment range of plus or minus 1.5 mm lets the drawer front be moved horizontally, which helps straighten reveals against the cabinet face and balance clearances side to side.
• Depth adjustment range of plus 3.0 mm forward adjustment on the 3D version shifts the front in the in-and-out direction, which helps flush the drawer face with doors or surrounding panels.
• The design provides 2D or 3D adjustment depending on version, so shops can use the same family of hardware for simpler or more demanding alignment requirements without changing drilling patterns.
• It is described as lightweight, high strength material, which supports repeated adjustment and everyday operation without adding unnecessary weight to the drawer box.

Dynapro Front Clip Mounting And Drilling Details

This Grass America front locking device is noted as a Dynapro 3D left-hand front clip with flange, so it is intended to mount at the left front corner of a Dynapro drawer setup where the flange contacts the drawer member. The web description states that pre-drilling is recommended with a 3/32 inch, or 2.5 mm, bit, which guides drill size selection when preparing the drawer box for mounting. This recommended bit diameter helps create pilot holes that accept typical fasteners for this component while reducing the risk of splitting the drawer material. Because it is specified for a minimum inside drawer width of 5-7/8 inches, or 150 mm, this dimension also informs layout when planning drawer box sizes around Dynapro slide hardware and front clips.

How This Dynapro Front Clip Supports Work

Where This Dynapro 3D Locking Device Fits

The product is identified as a Dynapro 3D left-hand front locking device with flange, so it occupies the left-hand front position in a Dynapro drawer system where the drawer front meets the slide hardware. Being defined for standard width or inset drawers means it can be used when the drawer front overlays the cabinet opening or when the front is set inside the face frame or case, keeping part selection consistent across different cabinet designs. The minimum inside drawer width of 5-7/8 inches, or 150 mm, indicates that drawers at or above this interior size can accept the component, which is helpful when laying out narrow versus wider drawers in a run. Its role as a front locking device means it connects the drawer front to the runner system in a way that also permits adjustment, aligning with the needs of modern concealed slide installations.

Adjustment Ranges That Reduce Drawer Rework

The web description states that the device provides 2D or 3D adjustment for drawers, so installers can fine-tune drawer fronts after the box and slides are in place instead of relying entirely on initial drilling accuracy. The height adjustment range of plus 3.5 mm allows the drawer front to be lifted relative to the box, which helps correct small layout variances and achieve consistent top margins under a countertop or rail. Side adjustment of plus or minus 1.5 mm lets the front shift left or right, so adjacent drawer fronts in a stack can be visually aligned by turning the adjustment rather than remaking parts. The depth adjustment range of plus 3.0 mm forward adjustment on the 3D version changes how far the front projects, which is useful when matching the plane of neighboring doors or when working in frameless cabinets where flush alignment is visible. Its lightweight, high strength material supports these adjustments without adding significant mass to the drawer assembly, which is valuable on larger drawer widths where hardware weight can accumulate.

Common Questions About This Dynapro Locking Device

Selecting This Dynapro Front Clip For Your Drawers

This Grass America Dynapro 3D left-hand front locking device with flange combines defined height, side, and depth adjustment ranges with lightweight, high strength material, giving cabinet shops a controllable way to align drawer fronts. Its suitability for standard width or inset drawers, along with the specified minimum inside drawer width of 5-7/8 inches, or 150 mm, ties directly into project layout decisions. The recommended 3/32 inch, or 2.5 mm, pre-drill detail simplifies shop setup for consistent pilot holes. Choosing this F134108942233 front clip lets installers match Grass Dynapro drawer hardware with adjustment capabilities that support clean, repeatable drawer front alignment.