Liberty Classic Edge Series 5-1/16" (128 mm) Center to Center Satin Nickel Pull, - P34928-SN-C

128mm Classic Edge Pull Satin Nickel For Cabinets

128mm c/c classic edge pull satin nickel is a Liberty Classic Edge Series cabinet pull designed to give doors and drawers a consistent 5-1/16 inch (128 mm) center-to-center layout, which keeps drill patterns uniform across a run of cabinets. The 6 inch overall length provides enough hand clearance for a solid grip on standard cabinet fronts without crowding tight face frames. Its 1-1/4 inch projection sets the pull off the surface at a practical distance, helping fingers clear the door edge while staying close enough to avoid catching on clothing. A 5/8 inch width presents a slim front profile, which suits modern and traditional cabinet styles where a low visual footprint is preferred. The satin nickel finish supplies a muted metallic look that works with many hinge and faucet finishes in the same tone, helping installers coordinate visible hardware across a project.

Key Liberty Classic Edge Pull Job Advantages

• The 5-1/16 inch (128 mm) center-to-center dimension gives a repeatable drilling reference, so jigs and templates can be reused from one cabinet run to the next.
• The 6 inch overall length spans more of the drawer or door front, which spreads pull force over a wider area and supports a balanced appearance on wider faces.
• The 1-1/4 inch projection creates functional finger clearance from the cabinet surface, which supports comfortable opening for frequent-use doors and drawers.
• The 5/8 inch width keeps the pull visually light on the face, which helps it sit cleanly on narrow rails or smaller drawer fronts.
• The satin nickel finish offers a soft metallic sheen, which coordinates with other satin nickel decorative hardware in kitchen, bath, or shop projects.
• The zinc die cast material forms a solid one-piece body, which supports consistent dimensions pull-to-pull across multiple units on the same installation.

Installation Dimensions For Consistent Cabinet Layout

The 5-1/16 inch (128 mm) center-to-center measurement sets the hole spacing for this Liberty Hardware pull, which lets installers line up with standard metric-based cabinet drilling patterns. At 6 inches overall length, the pull slightly overhangs the hole spread, which visually centers the grip along the fastener line. The 1-1/4 inch projection defines how far the pull stands off the cabinet face, which matters when doors open near walls or adjacent appliances. With a 5/8 inch width, the pull fits comfortably on common rail heights without overlapping panel details or edge profiles on most standard cabinet doors.

Using This Liberty Classic Edge Pull In Projects

Where This Satin Nickel Cabinet Pull Performs Best

This Liberty Hardware Classic Edge pull sits in the Decorative Hardware & Moldings category, which positions it for visible cabinet door and drawer applications. The satin nickel finish suits installations where a subdued metal look is preferred over bright or polished finishes, such as contemporary kitchens or workrooms with brushed fixtures. The 6 inch length and 5-1/16 inch (128 mm) center-to-center sizing align with typical cabinet drawer widths, so a run of these pulls can carry a consistent visual line across banks of drawers. Because the body is zinc die cast, each pull follows the same molded profile, which helps maintain even sightlines when multiple units are mounted level across upper and lower cabinets.

Details That Support Repeatable Mounting And Alignment

The defined 128 mm center-to-center spacing on this Classic Edge pull lets installers use metric drilling guides, which speeds layout on European-style and frameless cabinet systems. On framed cabinets, the same 5-1/16 inch spacing works well with many standard jig settings, so holes land predictably on drawer fronts and stiles. The 1-1/4 inch projection ensures that once mounted, fingers can wrap behind the pull without contacting the cabinet face, which can reduce wear on finished surfaces over time. The 5/8 inch width helps the pull sit flat on narrow rails, so the mounting area stays fully supported across the contact surface. The satin nickel finish presents a consistent appearance from pull to pull, which keeps long runs of cabinets looking uniform when all fasteners are aligned on the same horizontal or vertical axis.

Common Questions About Liberty P34928-SN-C Pull

Select This Classic Edge Pull For Satin Nickel Runs

The Liberty Classic Edge Series P34928-SN-C pull combines a 5-1/16 inch (128 mm) center-to-center layout with a 6 inch body length, which fits standard cabinet drilling patterns and drawer widths. Its satin nickel finish and 5/8 inch width work well where a low-profile metal look is preferred on visible fronts. With a 1-1/4 inch projection and zinc die cast construction, this pull provides defined clearances and consistent dimensions that support straight lines across doors and drawers when laid out from the same reference points.