#8 x 1 inch flat head assembly screw describes a Wurth fastener designed for general assembly work where a flush head is needed, so panels or hardware sit flat against the surface after driving. The screw uses a flat head profile, which allows the head to sink into the material and leave a level surface that supports clean, finished joins. The #8 diameter provides a common, workhorse size used across many woodworking and shop assembly tasks, giving predictable holding strength in typical cabinet and fixture builds. The 1 inch length targets situations where bite into the substrate is needed without breaking through the opposite face, which helps on face frames, stretchers, and similar parts. This screw is identified by manufacturer part number 3670000361961 7000, which ties directly to Wurth Baer Supply ordering and reordering systems for consistent replenishment.
The Wurth #8 flat head assembly screw uses #2 square drive bits, which gives installers a familiar driver interface so they can work with standard square bits already used in many shops. The flat head geometry works with common countersinking, allowing the head to seat into the material so hardware or workpieces can stack or fit against that surface without rocking. For 1 inch lengths, the screw is threaded fully along the shank, which means every part of the embedded length contributes to holding power in the joint. The coarse thread and fully threaded 1 inch length together support strong grip over the entire embedment depth, which matters when fastening into shorter stock or thinner cabinet parts.
The Type 17 auger point on this Wurth #8 x 1 inch flat head assembly screw is shaped to begin cutting as soon as the tip engages the material, which helps the screw advance with a controlled bite in many wood-based substrates. That auger-style geometry promotes chip removal from the entry point, so material is cleared as the screw advances and the thread can seat into a cleaner path. This behavior is useful on assembly lines or in cabinet shops where screws are driven repeatedly into similar stock, because the point design supports a consistent starting feel from screw to screw. In practical terms, the combination of Type 17 point and coarse thread means the installer can bring parts together with fewer stalls at the start of driving, supporting a steady workflow during case assembly, face frame work, or fixture builds.
The coarse thread on this Wurth 3670000361961 7000 screw is spaced to remove material efficiently with each revolution, which lets the screw pull components together firmly in fewer turns during assembly. Because the 1 inch version is fully threaded, that coarse pattern continues along the full embedded length, so clamping force is distributed across the entire depth of the joint. The square drive head uses a #2 square interface, which gives the bit four flat engagement surfaces so torque is transferred reliably from driver to screw under load. That geometry helps the bit stay engaged as the coarse threads draw parts tight, which is valuable when working at arm's length or overhead where slipping would disrupt alignment. Together, the coarse threads, full-length threading on the 1 inch size, and square drive pairing support repeatable, efficient assembly work in shop and jobsite environments.
This Wurth assembly screw is a #8 diameter in a 1 inch length, so it suits many cabinet and general assembly tasks where moderate holding power is needed without excessive penetration.
The #8 x 1 inch flat head assembly screw uses a square drive that matches #2 square drive bits, helping drivers stay engaged when torque increases as joints tighten.
The 1 inch length of this screw is threaded fully along the shank, so threads engage across the entire embedded length and support grip in thinner cabinet or fixture parts.
The Type 17 auger point describes a tip geometry that starts easily and cuts as it advances, which supports smoother starts and reduces wandering at the entry point in many woods.
The coarse thread profile removes material quickly and bites firmly, so the screw pulls parts together efficiently and can provide strong holding power in typical assembly substrates.
This Wurth screw is case hardened with a zinc finish, giving a hardened outer surface and a zinc coating that supports performance in normal interior shop and cabinet environments.
The Wurth #8 x 1 inch flat head assembly screw with Type 17 auger point, coarse thread, and zinc finish is built for repeatable assembly work where a flush head and positive square drive engagement matter. Using a fully threaded 1 inch length, the screw engages material across the full embedment, supporting grip in many cabinet, fixture, and shop-built components. For buyers standardizing on a reliable #8 assembly fastener, ordering this specific Wurth 3670000361961 7000 screw from Wurth Baer Supply ties everyday assembly tasks directly to a consistent, repeatable fastener choice.
Sold In: 7000 Each
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 1 Each |  WW90210 Mfr# 0614176153961 1 | #2 x 1" Square Drive Insert Bit, 2 Piece Bit | ||||
Sold in: 1 Each |  WW90220 Mfr# 0614176139961 1 | #2 x 2" Square Drive Insert Bit, 2 Piece Bit | ||||
Sold in: 1 Each |  WW90230 Mfr# 0614176140961 1 | #2 x 3" Square Drive Insert Bit, 2 Piece Bit | ||||
Sold in: 1 Each |  WW90240 Mfr# 0614176142961 1 | #2 x 4" Square Drive Insert Bit, 2 Piece Bit | ||||
Sold in: 1 Each |  WW90260 Mfr# 0614176143961 1 | #2 x 6" Square Drive Insert Bit, 2 Piece Bit |